cable modem

Thread View: ahn.tech.linux

5 messages

[T] Back to Threads [V] Tree View [G] Group Articles

5 total messages Started by Niko Kononen Sun, 19 Nov 2000 00:00

#1230

Author: Niko Kononen
Date: Sun, 19 Nov 2000 00:00

2 lines
511 bytes

I just installed Red Hat Linux 7.0 and I don�t know how I can make my cable
work

Re: cable modem

#1235

Author: John Strauss
Date: Wed, 22 Nov 2000 00:00

10 lines
1009 bytes

If yours is like mine, you connect through an ethernet port and your service
is set through DHCP.  Set that port to DHCP, and it should take care of the
problem.
Niko Kononen <egf@pp.htv.fi> wrote in message
news:8v9469$efu$1@m3.pp.htv.fi...
> I just installed Red Hat Linux 7.0 and I don�t know how I can make my
cable
> work
>
>

Re: cable modem

#1243

Author: Yezid Acosta
Date: Fri, 24 Nov 2000 07:17

10 lines
1327 bytes

On Sun, 19 Nov 2000 19:53:53 +0200, "Niko Kononen" <egf@pp.htv.fi>
wrote:

I installed mine just fine but when I was setting up the network
feature I made sure to set it for DHCP since thats how my cable modem
was set up. Try setting it up to DHCP and it should work. 

>I just installed Red Hat Linux 7.0 and I don�t know how I can make my cable
>work
>

Re: cable modem

#1138

Author: Klingon
Date: Wed, 06 Dec 2000 03:42

12 lines
1435 bytes

The driver module needed is tulip.o  . It is needed to configure your
ethernet card (make sure it's a supported card (see Linux hardware
compatability list)  tulip.o will configure a few cards such as
Linksys LNE100TX. Other cards that are supported are the D-Link and of
course 3 Com cards (which do not use tulip.o)

On Sun, 19 Nov 2000 19:53:53 +0200, "Niko Kononen" <egf@pp.htv.fi>
wrote:

>I just installed Red Hat Linux 7.0 and I don�t know how I can make my cable
>work
>

Re: cable modem

#1149

Author: William Pelish
Date: Tue, 12 Dec 2000 07:02

19 lines
1672 bytes

My dlink does not work with tulip. Corel User.


"Klingon@URANUS.COM" <Santa@hohoho.com> wrote in message
news:kddr2t0o7u2inlochc8uvu9eie2q8vgimt@4ax.com...
> The driver module needed is tulip.o  . It is needed to configure your
> ethernet card (make sure it's a supported card (see Linux hardware
> compatability list)  tulip.o will configure a few cards such as
> Linksys LNE100TX. Other cards that are supported are the D-Link and of
> course 3 Com cards (which do not use tulip.o)
>
> On Sun, 19 Nov 2000 19:53:53 +0200, "Niko Kononen" <egf@pp.htv.fi>
> wrote:
>
> >I just installed Red Hat Linux 7.0 and I don�t know how I can make my
cable
> >work
> >
>

Thread Navigation

This is a paginated view of messages in the thread with full content displayed inline.

Messages are displayed in chronological order, with the original post highlighted in green.

Use pagination controls to navigate through all messages in large threads.

Back to All Threads