🚀 go-pugleaf

You need to add the word "nameserver" infront of the listing for your DNS
Servere in the /etc/resolv.conf for the DNS lookup to work properly.  In the
etc/hosts file, you need to change the line that has hosts to
hosts: files dns
You also need to add the file defaultrouter to the /etc/ directory and just
put in the gateway's IP address.
to check on the fly if you can reach your gateway, type in the following:

# route add default my.gateway.ip.address

This will do a 1 time gateway addition so that you can test out the setting.
If the route add default ... line does not work, then probably either your
subnet mask is improperly set up or your NIC is not setup / working
properly.


Matt Blair
MattRBlair@home.com

s wrote in message <37BCECE2.4BF28417@home.com>...
>i dont know if u need a cross over cable between the hub and the up link
>but i could be wrong try using a regulur calbe and make sure none of the
>box have the same ip
>
>schairez@home.com
>and if u can pleas help me set up my at home i cant ping the gate way or
>my DNS i have @home cable serves
>
>hi i have @home and cant ping my gate way 24.7.63.1 or my DNS
>24.0.200.33 or 24.0.200.34
>
>netmask 24.0.200.33 or 24.0.200.34
>my ip 24.7.63.1 I can ping my own ip but thats all
>network card is up and running fine but ndc400 nic card retek chipset
>RTL8029(AS)
>
>resolv.conf
>domain stana1.occa.home.com
>24.0.200.33
>24.0.200.34
>
>
>"my @home install data sheet"
>
>DHCP 24.1.8.70
>dns 24.0.200.33 and 24.0.200.34
>netmask 255.255.255.128
>subdomian stana1.occa.home.com
>broadcast "none"
>ip 24.7.63.9
>login schairez
>dns name or computer name = CC1003148-A
>mail server = mail
>directory server = directory
>news server =news
>web Proxy server name http://proxy:8080
>
>help my pleas thanks a lot
>
>
>
>
>hac wrote:
>>
>> Steven D. Nakhla wrote:
>> >
>> > I recently signed up for cable modem service.  Now, we have 2
computers, so
>> > I ordered an extra IP address for the other, and attempted to setup a
>> > network so the other computer could have access.  The other computer
uses
>> > only Win98 and my computer uses Win98, Linux, and Solaris.
>> >
>> > I bought the Intel InBusiness 5-Port 10 Mbps hub for our network.  I
was
>> > told to plug the cable modem into the uplink port on the hub.  However,
the
>> > hub doesn't have an uplink port.  It has only 5 standard ethernet
ports.
>> > So, using a crossover cable, I plugged the cable modem into one of the
>> > ports, and the other 2 computers into the next 2 ports.  I am able to
access
>> > the internet through either computer.  The problem is, I can't use both
at
>> > the same time.  Is this common?  Whenever I try and access the internet
when
>> > the other computer is on, I get network errors.  How can I set it up so
that
>> > both computers can access the internet at the same time?
>> >
>> > Could it be a problem with how I have the hub set up?  Has anyone had
>> > experience with this hub?  I could REALLY use any help that you all
could
>> > give me in setting this up.  Thanks!
>> >
>> There have been many reports of the MSO's failing to configure the
>> modems to use two IP's at the same time.  Your trouble sounds at lot
>> like the other reports.  Call and have them reconfigure the modem.
>>
>> --
>> Howard Christeller  Irvine, CA   hchristeller@home.com