🚀 go-pugleaf

Marc SCHAEFER wrote:
 
> Please also double-check that the SCSI adapter works (e.g. with a
> SCSI disk drive), and that there is no interrupt conflict.

Den Interuptkonflikt konnte ich l�sen. Die Karte wird jetzt mit 
  modprobe ncr53c8xx
initialisiert ( und das System st�rtzt nicht mehr ab ).
Folgende Meldungen werden ausgegeben :
---/var/log/messages------------------------------------------------

Mar 25 22:25:46 mot kernel: ncr53c8xx: at PCI bus 0, device 14, function
0
Mar 25 22:25:46 mot kernel: ncr53c8xx: 53c810a detected with Symbios
NVRAM
Mar 25 22:25:46 mot kernel: ncr53c810a-0: rev=0x23, base=0xe5000000,
io_port=0xec00, irq=9
Mar 25 22:25:46 mot kernel: ncr53c810a-0: Symbios format NVRAM, ID 7,
Fast-10, Parity Checking
Mar 25 22:25:46 mot kernel: ncr53c810a-0: initial
SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 00/00/00/00/00/00
Mar 25 22:25:46 mot kernel: ncr53c810a-0: final  
SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 03/ce/a0/00/08/00
Mar 25 22:25:46 mot kernel: ncr53c810a-0: resetting, command processing
suspended for 2 seconds
Mar 25 22:25:46 mot kernel: ncr53c810a-0: restart (scsi reset).
Mar 25 22:25:46 mot kernel: scsi0 : ncr53c8xx - version 3.2a-2
Mar 25 22:25:46 mot kernel: scsi : 1 host.
Mar 25 22:25:48 mot kernel: ncr53c810a-0: command processing resumed
Mar 25 22:25:51 mot kernel:   Vendor:     zF�   Model: n5 ����� �&�     
Rev:     
Mar 25 22:25:51 mot kernel:   Type:   Direct-Access                     
ANSI SCSI revision: 00
Mar 25 22:25:51 mot kernel: Detected scsi disk sda at scsi0, channel 0,
id 6, lun 0
                                          ^^^^                         
^^^^
                                          eigentlich mein Scanner an   
dieser id ?!?
Mar 25 22:25:51 mot kernel: ncr53c810a-0-<6,*>: device did not report
SYNC.
Mar 25 22:25:51 mot kernel: sda : sector size 0 reported, assuming 512.
Mar 25 22:25:51 mot kernel: SCSI device sda: hdwr sector= 512 bytes.
Sectors= 1 [0 MB] [0.0 GB]
Mar 25 22:25:51 mot kernel:  sda:scsidisk I/O error: dev 08:00, sector 0
Mar 25 22:25:51 mot kernel:  unable to read partition table
....
--------------------------------------------------------------------
Tja, der erste Schritt scheint zu klappen. Nun wird noch der Scanner mit
einer 
Festplatte verwechselt. 
----/proc/scsi/scsi-------------------------------------------------
Attached devices: 
Host: scsi0 Channel: 00 Id: 06 Lun: 00
  Vendor:     zF   Model: n5        &      Rev:     
  Type:   Direct-Access                    ANSI SCSI revision: ffffffff
--------------------------------------------------------------------

----/proc/scsi/ncr53c8xx/0------------------------------------------
General information:
  Chip NCR53C810a, device id 0x1, revision id 0x23
  IO port address 0xec00, IRQ number 9
  Using memory mapped IO at virtual address 0xc4911000
  Synchronous period factor 25, max commands per lun 32
--------------------------------------------------------------------

----sgcheck---------------------------------------------------------
/dev/sg0 0/0/6/0 Direct-Access zF n5        &
--------------------------------------------------------------------

Wie finde ich den Scanner ?

Merci en avance et cordiallement

Simon

-- 
--------------------------------------------------------------------
                                                      Simon Schmidig
                                              schmidi6@etus.unige.ch
PGP KeyID: 512/15974F7D FP: 0A8B 2D45 CA8F A407  6799 371F 3703 4B10