🚀 go-pugleaf

Hoi z�me

Die ISDN-Karte Teles S0/13.6c1 PNP kann ich zwar mit isapnp
konfigurieren (scheint mir jedenfalls so), aber wenn ich dann die
Daten hisax �bergebe, kann er die Karte nicht installieren. Nach dem
Syslog h�ngt es m.E. mit den IO-Adressen und dem HSCX zusammen, da
scheint was falsch zu sein, aber was bloss? Im Folgenden die
Fehlermeldungen im Syslog und sonst noch einige n�tzliche Angaben (f�r
diejenigen, die sich auskennen :-)) )

F�r L�sungsvorschl�ge bin ich dankbar. Falls jemand mir einen
Ratschlag hat, in welcher anderen Newsgroup ich am ehesten Hilfe
bekommen k�nnte, w�re ich auch schon (fast) gl�cklich. ;-)


thx, Strada

------------------------
modprobe-Aufruf:
modprobe hisax type=4 protocol=2 irq=9 io0=0x580 io1=0x180
---
Linux version 2.0.36
ISDN subsystem Rev: 1.44.2.9/1.41.2.11/1.48.2.27/1.28.2.2/1.8.2.2
---
HiSax: Linux Driver for passive ISDN cards
HiSax: Version 3.1 (module)
HiSax: Layer1 Revision 1.15.2.19
HiSax: Layer2 Revision 1.10.2.11
HiSax: TeiMgr Revision 1.8.2.7
HiSax: Layer3 Revision 1.10.2.6
HiSax: LinkLayer Revision 1.30.2.13
HiSax: Approval certification valid
HiSax: Approved with ELSA Quickstep series cards
HiSax: Approval registration numbers:
HiSax: German D133361J CETECOM ICT Services GmbH
HiSax: EU (D133362J) CETECOM ICT Services GmbH
HiSax: Total 1 card defined
HiSax: Card 1 Protocol EDSS1 Id=HiSax (0)
HiSax: Teles IO driver Rev. 1.11.2.9
HiSax: Creatix/Teles PnP config irq:9 isac:0x580  cfg:0x0
HiSax: hscx A:0x180  hscx B:0x1A0
Teles3: ISAC version (ff): 2085 V2.3
Teles3: HSCX version A: ???  B: ???
Teles3: wrong HSCX versions check IO address
HiSax: Card Creatix/Teles PnP not installed !
---
isapnp-Ausgabe
Board 1 has Identity 28 0a 49 5c c0 10 26 27 50:  TAG2610 Serial No
172580032 [checksum 28]
Peek(TAG2610/172580032)[0][0x60](IO  0) is 0x0580, (5,128)
Peek(TAG2610/172580032)[0][0x62](IO  1) is 0x0180, (1,128)
Peek(TAG2610/172580032)[0][0x70](INT 0) is 0x0902, (9,2)
---
isapnp.conf:
# Trying port address 0203
# Board 1 has serial identifier 28 0a 49 5c c0 10 26 27 50

# (DEBUG)
(READPORT 0x0203)
(ISOLATE)
(IDENTIFY *)

# Card 1: (serial identifier 28 0a 49 5c c0 10 26 27 50)
# TAG2610 Serial No 172580032 [checksum 28]
# Version 1.0, Vendor version 1.0
# ANSI string -->TELES.S0/16.3c Plug&Play<--
#
# Logical device id TAG2610
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be
changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE TAG2610/172580032 (LD 0

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0580
#             Maximum IO base address 0x05b8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 2
(IO 0 (BASE 0x580))
(IO 0 (PEEK))
(IO 1 (BASE 0x180))
(IO 1 (PEEK))
#       IRQ 3, 4, 5, 9, 10, 11, 12 or 15.
#             High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 9 (MODE +E)))
(INT 0 (PEEK))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0500
#             Maximum IO base address 0x05b8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 2
# (IO 0 (BASE 0x0500))
#       IRQ 10, 11 or 12.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 10 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0680
#             Maximum IO base address 0x06b8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 2
# (IO 0 (BASE 0x0680))
#       IRQ 10, 11 or 12.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 10 (MODE +E)))

#       Start dependent functions: priority functional
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x1500
#             Maximum IO base address 0x17f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 2
# (IO 0 (BASE 0x1500))
#       IRQ 3, 4, 5, 9, 10, 11, 12 or 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#     End dependent functions
#     Vendor defined tag:  84 0d 00 00 00 00 00 00 00 00 00 00 00 00
#     Vendor defined tag:  84 06 00 00 00 00 00
(ACT Y)))
# End tag... Checksum 0x00 (OK)
---
/proc/interrupts:
 0:     157596   timer
 1:          2   keyboard
 2:          0   cascade
10:       1506   3c509
11:       6036   aha1542
13:          1   math error
14:          0 + ide0
---
/proc/ioports:
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0080-009f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : npu
01f0-01f7 : ide0
0278-027f : lp
02e8-02ef : serial(auto)
02f8-02ff : serial(auto)
0300-030f : 3c509
0330-0333 : aha1542
0378-037f : lp
03c0-03df : vga+
03e8-03ef : serial(auto)
03f0-03f5 : floppy
03f6-03f6 : ide0
03f7-03f7 : floppy DIR
03f8-03ff : serial(auto)