🚀 go-pugleaf

I have installed an IGS to IGS link over a 64Kbps line.

The router at my end becomes very very slow, every couple of days or so.
On inspection of interfaces, buffers, cpu and protocol interfaces
I can't see anything that is startling or anything that would slow it
down! 50% of pings to the IGS over ethernet would be lost.

I have been reloading it just to get the users going again,
but today I found that a "clear int ethernet 0" command
fixes the problem.

Is this a known problem?

Strange that a manual interface reset is required!

The router version is:

IGS-BR Software, Version 8.2(6) 
Copyright (c) 1986-1991 by cisco Systems, Inc.
Compiled Tue 17-Sep-91 09:00 by dchan

System Bootstrap, Version 4.3(4) 

SMM3R uptime is 1 day, 15 hours, 3 minutes
System restarted by reload
Running default software

cisco IGS (68020) processor (revision I) with 1024K bytes of memory.
Processor board serial number 00267514
Bridging software.
1 Ethernet/IEEE 802.3 interface.
1 Serial network interface.
16K bytes of non-volatile configuration memory.
Configuration register is 0x101
 
 
Ethernet 0 is up, line protocol is up 
  Hardware type is Lance, hardware address is aa00.0400.52c8
  Internet address is 134.18.16.10, subnet mask is 255.255.255.0
  MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255
  Encapsulation ARPA, loopback not set, keepalive set (10 sec)
  ARP type: ARPA, HP-PROBE, ARP Timeout 4:00:00
  Last input 0:00:00, output 0:00:00, output hang never
  Output queue 0/40, 0 drops; input queue 0/75, 11 drops
  Five minute input rate 6000 bits/sec, 10 packets/sec
  Five minute output rate 1000 bits/sec, 2 packets/sec
     1039264 packets input, 98259285 bytes, 21 no buffer
     Received 986842 broadcasts, 0 runts, 0 giants
     67 input errors, 17 CRC, 13 frame, 0 overrun, 50 ignored, 0 abort
     101542 packets output, 32843438 bytes
     0 output errors, 813 collisions, 7 interface resets, 0 restarts

Serial 0 is up, line protocol is up 
  Hardware type is MK5025
  Interface is unnumbered.  Using address of Ethernet0 (134.18.16.10)
  MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, rely 255/255, load 7/255
  Encapsulation HDLC, loopback not set, keepalive set (10 sec)
  Last input 0:00:03, output 0:00:00, output hang never
  Output queue 0/40, 9 drops; input queue 0/75, 0 drops
  Five minute input rate 0 bits/sec, 0 packets/sec
  Five minute output rate 2000 bits/sec, 3 packets/sec
     68096 packets input, 9868207 bytes, 2 no buffer
     Received 42734 broadcasts, 0 runts, 0 giants
     11 input errors, 11 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     372762 packets output, 50019023 bytes
     0 output errors, 0 collisions, 1397 interface resets, 0 restarts
     0 carrier transitions


Protocols that are supported are:
	TCP/IP
	Decnet
	Appletalk PhaseII
	Bridging LAT & MOP

Any help here would be appreciated,
-- 
Darrell Boon				Phone   :  +61-49-401-675
Senior Systems Engineer			Fax     :  +61-49-402-165
BHP Information Technology		Internet:  darrell@bhpese.oz.au
P.O. Box 216 Hamilton 2303 AUSTRALIA