🚀 go-pugleaf

In article <ASM370%90021600224921@OHSTVMA.BITNET> Wazawa Tetsuichi
<TAB1KAC@JPNTOHOK.BITNET> writes:
> I wrote a test program using extended parameter list as bellow. But it
>doesn't work. That is, the parameters I type on command line cannot be
>referred by the module generated by the assembly source. Can anyone
>point out what I mistake?
>
>Thanks in advance                      Tetsuichi Wazawa
>                                       Dept.of Science, Biological Institute
>                                       Tohoku University
>
>--------------------------- Cut Here -----------------------------------------
>
>*
>         PRINT GEN
>         START 0
>         STM   14,12,12(13)
>         BALR  12,0
>         USING BEGIN,12
>*
>         LA    3,ADRCMD
>         MVC   0(4,3),0(0)
>         LA    3,ADRARST
>         MVC   0(4,3),4(0)
>         LA    3,ADRAREN
>         MVC   0(4,3),8(0)
>         L     3,ADRCMD
>         LA    4,BUF
>         MVC   0(8,4),0(3)
>         WRTERM BUF,8
>         L     3,ADRARST
>         LA    4,BUF
>         MVC   0(30,4),0(3)
>         WRTERM BUF,30
>         LM    14,12,12(13)
>         SR    15,15
>         BR    14
>*
>ADRCMD   DS    A
>ADRARST  DS    A
>ADRAREN  DS    A
>BUF      DC    80X'40'
>         END

Try the following modification:

         PRINT GEN
MY       CSECT ,
         USING MY,R12
         STM   R14,R12,12(R13)
         LR    R12,R15
*
         LR    R10,R0                  Transfer EPLIST address
         USING EPLIST,R10
         L     R4,EPLCMD               Find command token address
         WRTERM (R4),8                 Write what is at that address
         L     R4,EPLARGBG             Get argument begin address
         L     R3,EPLARGND             And argument end address
         SLR   R3,R4                   Get length of arguments
         WRTERM (R4),(R3)              Write them on the console
         LM    R14,R12,12(R13)         Restore caller's registers
         SR    R15,R15                 Set return and condition codes
         BR    R14                     Return to caller
         EPLIST
         END   ,

The primary thing wrong with what you did was that you tried to use R0 as an
address register. This is not possible. Any time R0 is used in an address
calculation, the value of it is always assumed to be 0, regardless of what
may actually be in it. There are reasons for this, and it can be handy to
exploit this behavior. But you must watch out for it too.

Similarly, when R0 is used as the register in an EXecute instruction, the value
in it is also assumed to be 0, regardless of what may actually be in it. This
makes it possible to execute an instruction remotely which you do not actually
want to alter, without clearing a register first.

R0 is generally used as the base for NUCON or (in CP) for PSA. This is because
these dsects map the first page of (maybe virtual) storage and WANT to have a
base address of 0. So USING NUCON,R0 gives you a base register for free,
because you can use R0 for other things while also using it as NUCON base.

Notice also in my changed example that it is NOT necessary to copy the values
from the EPLIST before referencing them. You are not making any kind of call
that requires CMS to build an EPLIST and so yours will remain uncorrupted.

I hope this helps you.

Michael Johnson                           "We are the Priests of the Temples
University of Maine System                 of Syrinx. Our great computers fill
Computing and Data Processing Services     the hallowed halls."
michael@maine.maine.edu                                      -- Neil Peart