🚀 go-pugleaf

In article <4025@mit-caf.MIT.EDU> shers@mit-caf.UUCP  writes:
>Vi   C
>----||----*-- Vo
>          |
>          /
>          \ R
>          /
>          \
>          |
>          GND
>         
>I need help in finding the right circuit for my thesis.  Basically,
>I am designing a highpass RC filter whose break point frequency is as
>small as I can get.  C is fixed at 1pF, so the objective is to make R big.
>Thus, what I need is a biasing network that will keep the node Vo 
>at 2.5 V DC, while making the R huge.  The supply voltages are 0 V and 5 V,
>which is why I want an approximately 2.5 V DC level.  It looks like what
>I want is a voltage source with a huge source impedance (1 Gohm would 
>be nice).  It doesn't have to be linear, the whole circuit doesn't have
>to be linear.

Another person replied with a configuration using a large resistor connected
to Vdd and another to Vss.  This, however, is not necessary.  Instead
one could connect a large resistor to a 2.5V voltage source (which has
a relatively low Thevenin resistance for the problem).  Creating a 2.5V voltage
source can be done using a voltage divider with resistors or
transistors (Gregorian & Temes p. 127).  Creating the large series
resistance to the 2.5V source is again the hard part.  I simulated
a few configurations below with two transistors (one of which will
be in the subthreshold region).  These are similar to using two
back to back diodes.  The simulations gave promising results.
Note:  The models used are from MOSIS and we do not measure
subthreshold currents nor try to model them.
The BSIM model and LEVEL=2 models gave answers different by an order
of magnitude.

Two other thought:
1) Use a MOSFET with drain connected to 2.5V and source connected to
   your output.  Then connect the gate to a very high frequency clock
   with a very low duty cycle.  (Variations on this theme are of
   course possible using two devices, one connected to Vdd and the
   other to Vss).
2) Use an amplifier with very high output impedance, connected so
   that it acts as a resistor.

-David Tornheim

--------------------------------------------------
High Output Impedance

VS 1 0 2.5V
RS 1 2 100
M1 2 3 3 3 CMOSN W=3UM L=2UM NRS=0 NRD=0
M2 4 3 3 3 CMOSN W=3UM L=2UM NRS=0 NRD=0
VO 4 0
*R1 4 0 1E20

.OPT NOMOD
.INCLUDE  M98T LEVEL=2 model
.INCLUDE  M98T LEVEL=4 model

*.OP
.DC VO 0V 5V 0.1V
.PRINT I(VO)

.ALTER
M1 3 2 2 2 CMOSP W=3UM L=2UM NRS=0 NRD=0
M2 3 4 4 4 CMOSP W=3UM L=2UM NRS=0 NRD=0
.ALTER
M1 3 2 2 2 CMOSN W=3UM L=2UM NRS=0 NRD=0
M2 3 4 4 4 CMOSN W=3UM L=2UM NRS=0 NRD=0
.ALTER
M1 3 2 2 0 CMOSN W=3UM L=2UM NRS=0 NRD=0
M2 3 4 4 0 CMOSN W=3UM L=2UM NRS=0 NRD=0
.ALTER
M1 3 2 2 2 PC1_NM1_DU1 W=3UM L=2UM NRS=0 NRD=0
M2 3 4 4 4 PC1_NM1_DU1 W=3UM L=2UM NRS=0 NRD=0
.END