🚀 go-pugleaf

I've an HP Omnibook Xe2 with a Trident CyberBlade i7 video card, it should
be supported by newer versions of XFree such as XFree86 3.6 or XFree86 4.0
but I can't make it work! I've installed Linux Red Hat 6.0 with XFree 3.3
first and XFree 3.6 after but the graphic can't start. I've also tried to
enable the VESA frame buffer by adding the line VGA=789 in my lilo.conf and
by using the XFree86_FBDEV server but the message is:


XFree86 Version 3.3.3.1 / X Window System
(protocol Version 11, revision 0, vendor release 6300)
Release Date: January 4 1999
 If the server is older than 6-12 months, or if your card is newer
 than the above date, look for a newer version before reporting
 problems.  (see http://www.XFree86.Org/FAQ)
Operating System: Linux 2.2.1-ac1 i686 [ELF]
Configured drivers:
   FBDev: Server for frame buffer device
   (Patchlevel 10): mfb, cfb8, cfb16, cfb24, cfb32
(using VT number 7)

XF86Config: /usr/X11R6/lib/X11/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) XKB: keycodes: "xfree86"
(**) XKB: types: "default"
(**) XKB: compat: "default"
(**) XKB: symbols: "us(pc101)"
(**) XKB: geometry: "pc"
(**) XKB: rules: "xfree86"
(**) XKB: model: "pc101"
(**) XKB: layout: "it"
(**) Mouse: type: PS/2, device: /dev/mouse, buttons: 3
(**) Mouse: 3 button emulation (timeout: 50ms)
(**) FBDev: Graphics device ID: "CyberBlade"
(**) FBDev: Monitor ID: "LCD Panel 800x600"
(--) FBDev: Mode "800x600" needs hsync freq of 48.08 kHz. Deleted.
(--) FBDev: Mode "800x600" needs hsync freq of 55.84 kHz. Deleted.
(--) FBDev: Mode "800x600" needs hsync freq of 64.02 kHz. Deleted.
(**) FontPath set to "unix/:-1"
(**) FBDev: Using XF86Config video mode database

Fatal server error:
No valid modes found.

same as when I try with XFree86_SVGA server.
I've configured the server by editing the XF86Config file as:

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

    RgbPath "/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (they are concatenated together)
# By default, Red Hat 6.0 and later now use a font server independent of
# the X server to render fonts.

    FontPath   "unix/:-1"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

    # Uncomment this to cause a core dump at the spot where a signal is
    # received.  This may leave the console in an unusable state, but may
    # provide a better stack trace in the core dump to aid in debugging
    #NoTrapSignals

    # Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
    # This allows clients to receive this key event.
    #DontZap

    # Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
    # sequences.  This allows clients to receive these key events.
    #DontZoom

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Keyboard section
# **********************************************************************

Section "Keyboard"

    Protocol    "Standard"

    # when using XQUEUE, comment out the above line, and uncomment the
    # following line
    #Protocol   "Xqueue"

    AutoRepeat  500 5

    # Let the server do the NumLock processing.  This should only be
    # required when using pre-R6 clients
    #ServerNumLock

    # Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
    #Xleds      1 2 3

    #To set the LeftAlt to Meta, RightAlt key to ModeShift,
    #RightCtl key to Compose, and ScrollLock key to ModeLock:

    LeftAlt        Meta
    RightAlt        Meta
   ScrollLock      Compose
   RightCtl        Control

# To disable the XKEYBOARD extension, uncomment XkbDisable.

#    XkbDisable

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:
#    XkbModel    "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
#    XkbModel    "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#    XkbLayout   "de"
# or:
#    XkbLayout   "de"
#    XkbVariant  "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#    XkbOptions  "ctrl:swapcaps"

# These are the default XKB settings for XFree86
#    XkbRules    "xfree86"
#    XkbModel    "pc101"
#    XkbLayout   "us"
#    XkbVariant  ""
#    XkbOptions  ""

   XkbKeycodes     "xfree86"
   XkbTypes        "default"
   XkbCompat       "default"
   XkbSymbols      "us(pc101)"
   XkbGeometry     "pc"
   XkbRules        "xfree86"
   XkbModel        "pc101"
    XkbLayout       "it"
EndSection

# **********************************************************************
# Pointer section
# **********************************************************************

Section "Pointer"
    Protocol    "PS/2"
    Device      "/dev/mouse"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

#    Protocol "Xqueue"

# Baudrate and SampleRate are only for some Logitech mice

#    BaudRate 9600
#    SampleRate 150

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

    Emulate3Buttons
    Emulate3Timeout    50

# ChordMiddle is an option for some 3-button Logitech mice

#    ChordMiddle

EndSection


# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "LCD Panel 800x600"
    VendorName  "Unknown"
    ModelName   "Unknown"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    HorizSync   31.5-37.9

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    VertRefresh 56-62

# 800x600 @ 56 Hz, 35.15 kHz hsync
ModeLine "800x600"     36     800  824  896 1024   600  601  603  625
# 800x600 @ 60 Hz, 37.8 kHz hsync
Modeline "800x600"     40     800  840  968 1056   600  601  605  628 +hsync
+vsync
# 800x600 @ 72 Hz, 48.0 kHz hsync
Modeline "800x600"     50     800  856  976 1040   600  637  643  666 +hsync
+vsync
# 800x600 @ 85 Hz, 55.84 kHz hsync
Modeline  "800x600"    60.75  800  864  928 1088   600  616  621
 657 -HSync -VSync
# 800x600 @ 100 Hz, 64.02 kHz hsync
Modeline  "800x600"    69.65  800  864  928 1088   600  604  610
 640 -HSync -VSync
EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Device configured by myself :

Section "Device"
    Identifier  "CyberBlade"
    VendorName  "Trident"
    BoardName   "CyberBlade i7"
    VideoRam    4096
    Clocks  25.18
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# The Colour SVGA server

Section "Screen"
    Driver      "svga"
    Device      "CyberBlade"
    Monitor     "LCD Panel 800x600"
    Subsection "Display"
        Depth       8
        Modes       "800x600"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes       "800x600"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       32
        Modes       "800x600"
        ViewPort    0 0
    EndSubsection
EndSection

# The frame buffer server

Section "Screen"
    Driver      "fbdev"
    Device      "CyberBlade"
    Monitor     "LCD Panel 800x600"
    Subsection "Display"
        Depth       8
        # Omit the Modes line for the "Generic VGA" device
        Modes       "800x600"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes       "800x600"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       32
        Modes       "800x600"
        ViewPort    0 0
    EndSubsection
EndSection

I can't understand what doesn't work with my graphic card, so I pray someone
to help me to resolve this problem. Thanks for all!!!