🚀 go-pugleaf

Hello all, 

after some trouble with the X-server that came with my graphics card
(Yakumo Voodoo Rush 3D with Alliance Promotion AT25 chip) I upgraded
to the latest version 3.3.3.1 of Xfree86 X Window System. In contrast
to that server provided by my graphics card vendor the new XF86_SVGA
server detects the chipset and my font path and tries to start, but it
never gets past this:

XFree86 Version 3.3.3.1 / X Window System
(protocol Version 11, revision 0, vendor release 6300)
Release Date: December 29 1998
	If the server is older than 6-12 months, or if your card is
newer
	than the above date, look for a newer version before reporting
	problems.  (see http://www.XFree86.Org/FAQ)
Operating System: Linux 2.0.35 i686 [ELF] 
Configured drivers:
  SVGA: server for SVGA graphics adaptors (Patchlevel 0):
      NV1, STG2000, RIVA128, RIVATNT, ET4000, ET4000W32, ET4000W32i,
      ET4000W32i_rev_b, ET4000W32i_rev_c, ET4000W32p,
ET4000W32p_rev_a,
      ET4000W32p_rev_b, ET4000W32p_rev_c, ET4000W32p_rev_d, ET6000,
ET6100,
      et3000, pvga1, wd90c00, wd90c10, wd90c30, wd90c24, wd90c31,
wd90c33,
      gvga, ati, sis86c201, sis86c202, sis86c205, sis86c215,
sis86c225,
      sis5597, sis5598, sis6326, tvga8200lx, tvga8800cs, tvga8900b,
      tvga8900c, tvga8900cl, tvga8900d, tvga9000, tvga9000i,
tvga9100b,
      tvga9200cxr, tgui9400cxi, tgui9420, tgui9420dgi, tgui9430dgi,
      tgui9440agi, cyber9320, tgui9660, tgui9680, tgui9682, tgui9685,
      cyber9382, cyber9385, cyber9388, cyber9397, cyber9520,
3dimage975,
      3dimage985, clgd5420, clgd5422, clgd5424, clgd5426, clgd5428,
      clgd5429, clgd5430, clgd5434, clgd5436, clgd5446, clgd5480,
clgd5462,
      clgd5464, clgd5465, clgd6205, clgd6215, clgd6225, clgd6235,
clgd7541,
      clgd7542, clgd7543, clgd7548, clgd7555, clgd7556, ncr77c22,
ncr77c22e,
      cpq_avga, mga2064w, mga1064sg, mga2164w, mga2164w AGP, mgag200,
      mgag100, oti067, oti077, oti087, oti037c, al2101, ali2228,
ali2301,
      ali2302, ali2308, ali2401, cl6410, cl6412, cl6420, cl6440,
video7,
      ark1000vl, ark1000pv, ark2000pv, ark2000mt, mx, realtek,
s3_virge,
      AP6422, AT24, AT3D, s3_svga, NM2070, NM2090, NM2093, NM2097,
NM2160,
      NM2200, ct65520, ct65525, ct65530, ct65535, ct65540, ct65545,
ct65546,
      ct65548, ct65550, ct65554, ct65555, ct68554, ct69000, ct64200,
      ct64300, mediagx, V1000, V2x00, p9100, spc8110, generic
(using VT number 7)

XF86Config: /etc/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) Mouse: type: Microsoft, device: /dev/mouse, baudrate: 1200
(**) Mouse: buttons: 3, Chorded middle button
(**) SVGA: Graphics device ID: "Yakumo"
(**) SVGA: Monitor ID: "Visa"
(--) SVGA: Mode "1600x1200" needs hsync freq of 105.77 kHz. Deleted.
(--) SVGA: Mode "1800X1440" needs hsync freq of 104.52 kHz. Deleted.
(**) FontPath set to
"/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/75dpi/,/usr/X11R6/lib/X11/fonts/100dpi/"
(--) SVGA: PCI: Alliance Semiconductor Unknown chipset (0x643d) rev 2,
Memory @ 0xfe000000, I/O @ 0xffa0
(--) SVGA: chipset:  AT3D
(**) SVGA: videoram: 6110k
(**) SVGA: Using 8 bpp, Depth 8, Color weight: 666
(--) SVGA: Maximum allowed dot-clock: 175.500 MHz
(**) SVGA: Mode "640x480": mode clock =  45.800
(**) SVGA: Mode "800x600": mode clock =  69.650
(**) SVGA: Mode "1024x768": mode clock = 115.500
(--) SVGA: There is no mode definition named "1280x1024"
(--) SVGA: Removing mode "1280x1024" from list of valid modes.
(--) SVGA: Virtual resolution set to 1024x768
(--) SVGA: Generic SpeedUps selected (Flags=0x30)
(--) SVGA: AT3D: Using linear framebuffer at 0xFE000000 (PCI bus)
(--) SVGA: AT3D: Using hardware cursor
(--) SVGA: Using XAA (XFree86 Acceleration Architecture)
(--) SVGA: XAA: Solid filled rectangles
(--) SVGA: XAA: Screen-to-screen copy
(--) SVGA: XAA: CPU to screen color expansion (bitmap, stipple,
TE/NonTE imagetext, TE/NonTE polytext)
(--) SVGA: XAA: Using 8 128x128 areas for pixmap caching
(--) SVGA: XAA: Caching tiles and non-transparent stipples
(--) SVGA: XAA: General lines and segments

Fatal server error:
Hung in ApmSync()


When reporting a problem related to a server crash, please send
the full server output, not just the last messages

_X11TransSocketUNIXConnect: Can't connect: errno = 111
giving up.
xinit:  Connection refused (errno 111):  unable to connect to X server
xinit:  No such process (errno 3):  Server error.

My question: What does this Hung in ApmSync() mean? And how can this
problem be solved?

Thank you very much for any hint in advance!

Cheers

Gerd

Gerd

P.S.: System: 486DX4/100 mit 32 MB, 10 GB Festplatte und Linux
Slackware 3.1 mit Kernel 2.0.36