🚀 go-pugleaf

yep, out of luck unfortunately

"gcd" <gcdmelbSPAM@austarmetro.com.au> wrote in message
news:405c3fd6@news.comindico.com.au...
> In Melbourne - a ways away from you if i read your email address right.
>
> Greg
>
> "Dave T." <417ci-ohc-v8@Perth.com.au> wrote in message
> news:405c32da$0$22513$5a62ac22@freenews.iinet.net.au...
> > where abouts are you ?
> >
> > "gcd" <gcdmelbSPAM@austarmetro.com.au> wrote in message
> > news:405c212c@news.comindico.com.au...
> > > Hi Dave,
> > > thanks for the info. I applied some machine oil in one or 2 places but
> > still
> > > no go. All the mechanisms seems to work OK by hand.
> > >
> > > When it first rotates backards, the clutch bounces back & forth. When
> the
> > > print heads are over at the LHS it engages and disengages the clutch
by
> > > moving to the left a small amount and the clutch does engage
disengage,
> > i've
> > > tried moving the head over there manually. I assume this is to feed a
> page
> > > in, but even at that point when the clutch is pushed forward ,or not
> > > depending on position of the print heads, it will not feed in a page.
> > >
> > > I picked this up cheap 12 months ago, it was bundled with a camera.
Had
> no
> > > need for the printer till now so have only just opened the box.
> > >
> > > Thanks again
> > > Greg
> > >
> > >
> > > "Dave T." <417ci-ohc-v8@Perth.com.au> wrote in message
> > > news:405ad29d$0$22526$5a62ac22@freenews.iinet.net.au...
> > > > The rollers initially roll backwards to unhook the pickup roller
> clutch,
> > > > predictably it will engage when the rollers proceed to go forwards.
> The
> > > > grease dries out and causes things such as this if it cant engage.
> > > >
> > > > "gcd" <gcdmelbSPAM@austarmetro.com.au> wrote in message
> > > > news:405ace36@news.comindico.com.au...
> > > > > Hi,
> > > > > I 've got a CP1160 printer and it will not feed paper when the
unit
> is
> > > 1st
> > > > > tuned on. This unit has been sitting in it's box for the last 12
> > months
> > > > and
> > > > > is new in box. The clutch grinds when 1st turned on and when the
> print
> > > > head
> > > > > gets to the left hand side the paper doesn't feed in. The lifter
for
> > the
> > > > > paper carriage doesn't lift
> > > > >
> > > > > When 1st turned on the paper rollers feed backwards (from the top,
> > > around
> > > > > toward the back of the printer) and when the print head goes to
the
> > lhs
> > > > the
> > > > > rollers feed forward.
> > > > >
> > > > > if manually rotated from the duplexer side the mechanism appears
to
> > > work.
> > > > ie
> > > > > if i feed the rollers forward when powered off the paper mechanism
> > picks
> > > > up
> > > > > a sheet.
> > > > >
> > > > > Anyone have any ideas?
> > > > >
> > > > > The paper feed motor wouldn't be powered backwards would it ?
> > > > >
> > > > > Anyone have a service manual  i could get electronically ?
> > > > >
> > > > > Many thanks
> > > > > -- 
> > > > > gcd  (delete everything else) A.T. austarmetro.com.au
> > > > >
> > > > > Greg
> > > > >
> > > > >
> > > >
> > > >
> > >
> > >
> >
> >
>
>