🚀 go-pugleaf

RetroBBS NetNews Server

Inspired by RockSolid Light RIP Retro Guy

Thread View: comp.periphs.scsi
1 messages
1 total messages Started by Anthony White Thu, 22 Nov 2001 12:59
More problems with error codes from SCSI system
#17269
Author: Anthony White
Date: Thu, 22 Nov 2001 12:59
100 lines
4592 bytes
Hi again Experts,

I have posted in the past on this issue but have come to a brick wall and
can not work out what the problem is:-((

Just a recap:

My Yamaha SCSI CD-ROM writer/re-writable decides
to stop working during a recording.

The fault condition is there even when the drive is
writing in 'dummy' mode.

I have tried to "decode" the SCSI error codes but can
not get anything sensible out of it.

Cane someone please help me out here.  I am not sure
if this is a bug in Linux (Using kernel 2.4.7-10 from Redhat
7.2) or if it is a problem with the drive.  Could it be a SCSI
bus problem or the Adaptec controller (Adaptec 29160)

All terminations are correct.  I have tried to slow the bus
down for the SCSI 50 pin that the CDWR runs of, no change.

Do I give up on SCSI, toss the drive and get an IDE?
All my drives are SCSI at present:-(

Could it be the drive that is not following standards?

The drive is a Yamaha CRW8824S

Awaiting some sort of input....

Tony

Note that the "\" means the next line is actually on the same line.

This is the output log:

Calling: /usr/lib/xcdroast-0.98/bin/xcdrwrap CDRECORD dev= "0,6,0" \
 fs=4096k  -v -useinfo speed=8 -dummy -eject -pad \
 -audio "/pub/img/track01.cdda.wav" ... 

scsidev: '0,6,0'
scsibus: 0 target: 6 lun: 0
Linux sg driver version: 3.1.19
pregap1: -1
Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 J�rg Schilling
TOC Type: 0 = CD-DA
Using libscg version 'schily-0.5'
atapi: 0
Device type    : Removable CD-ROM
Version        : 2CRW8824S
Response Format: 2
Capabilities   : SYNC
Vendor_info    : 'YAMAHA  '
Identifikation : 'CRW8824S        '
Revision       : '1.00'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags   : SWABAUDIO
Drive buf size : 3172848 = 3098 KB
FIFO size      : 4194304 = 4096 KB
[...image being copied...]
Total size:     422 MB (41:52.24) = 188418 sectors
Lout start:     422 MB (41:54/18) = 188418 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 4
Is not unrestricted
Is not erasable
ATIP start of lead in:  -11580 (97:27/45)
ATIP start of lead out: 333226 (74:05/01)
Disk type:    Short strategy type (Phthalocyanine or similar)
Manuf. index: 9
Manufacturer: Kodak Japan Limited
Blocks total: 333226 Blocks current: 333226 Blocks remaining: 144808
RBlocks total: 343358 RBlocks current: 343358 RBlocks remaining: 154940
Starting to write CD/DVD at speed 8 in dummy mode for single session.
0 seconds. Operation starts.
Waiting for reader process to fill input buffer ...
input buffer ready.
Starting new track at sector: 0

Track 01: Total bytes read/written: 41470464/41470464 (17632 sectors).
Starting new track at sector: 150069
cdrecord: Input/output error. write_g1: scsi sendcmd: no error
CDB:  2A 00 00 02 55 7E 00 00 1B 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 21 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x21 Qual 0x00 (logical block address out of range) Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 40.995s timeout 40s

Sense Bytes: 70 00 00 00 00 00 00 0A 00 00 00 00 00 00 00 00 00 00
write track data: error after 6794928 bytes
Writing  time:  341.863s
Fixating...
===================
Thread Navigation

This is a paginated view of messages in the thread with full content displayed inline.

Messages are displayed in chronological order, with the original post highlighted in green.

Use pagination controls to navigate through all messages in large threads.

Back to All Threads