Thread View: comp.sys.acorn.tech
3 messages
3 total messages
Started by Valerio Pulese
Wed, 18 Nov 1992 10:59
INFO:Step by step disassembler.
Author: Valerio Pulese
Date: Wed, 18 Nov 1992 10:59
Date: Wed, 18 Nov 1992 10:59
24 lines
1142 bytes
1142 bytes
I have downloaded sarah but it isn't what I need . (good piece of software however) Is there something that could do a step by step run-mode. Still waiting an answer for my article on parallel/econet socket. I retry : I need a high speed serial input (bit-stream). Parallel port could be very simple to read but which are its limits in frequency? Econet socket have been used by Vertical Twist.Could someone tell me some informations. Use news,email,snail mail,pidgeons,pony express... but pleeease reply. Thanks in advance. Best regards Valerio -- E-mail: valerio@sabrina.dei.unipd.it Man-mail: Valerio Pulese V.Volturno 23/7 30038 Spinea VENICE - ITALY
Re: INFO:Step by step disassembler.
Author: Graham Allan
Date: Wed, 18 Nov 1992 16:22
Date: Wed, 18 Nov 1992 16:22
20 lines
1640 bytes
1640 bytes
In article <Bxwrup.KIs@dei.unipd.it> valerio@sabrina.dei.unipd.it ( Valerio Pulese ) writes: > >I have downloaded sarah but it isn't what I need . >(good piece of software however) >Is there something that could do a step by step run-mode. Grasping at straws here, but wasn't there a debugger in the old Programmers Toolkit thing. Let's see, there was asd and something called either dbg or debug. One was the symbolic debugger; the other was a machine-code debugger which could, I think, single step through code. It could work through the serial port if you wanted to use an external terminal. This was back in Arthur days, so who knows if it still works under RISC OS 3.1? I don't think I've even used it under RISC OS 2... which is why I can't remember much about it! Anyway, if someone can confirm this would do the job, the toolkit package is long defunct, so you might be able to pick up a copy cheaply somewhere. I guess there must be similar (up-to-date) tools with Desktop C, or Assembler, but that's not much good to you. Graham allan@mnhep8.hep.umn.edu
Re: INFO:Step by step disassembler.
Author: T. Hennerich
Date: Mon, 23 Nov 1992 13:41
Date: Mon, 23 Nov 1992 13:41
30 lines
1719 bytes
1719 bytes
In article <1992Nov18.162248.28902@news2.cis.umn.edu> alla0008@student.tc.umn.edu (Graham Allan) writes: >In article <Bxwrup.KIs@dei.unipd.it> valerio@sabrina.dei.unipd.it ( Valerio Pulese ) writes: >> >>I have downloaded sarah but it isn't what I need . >>(good piece of software however) >>Is there something that could do a step by step run-mode. > >Grasping at straws here, but wasn't there a debugger in the old >Programmers Toolkit thing. Let's see, there was asd and something called >either dbg or debug. One was the symbolic debugger; the other was a >machine-code debugger which could, I think, single step through code. It >could work through the serial port if you wanted to use an external terminal. > The only debugger I know which can step trough assembler code is SSTEP It is shareware/Freeware/pd and available in some libraries. The problem is: it comes nearly without documentation .... I think (but do not know) the source-code-debugger of DDE-assembler can also step through a program. so long MUFTI -- T. Hennerich zrg40370@helpdesk.rus.uni-stuttgart.de
Thread Navigation
This is a paginated view of messages in the thread with full content displayed inline.
Messages are displayed in chronological order, with the original post highlighted in green.
Use pagination controls to navigate through all messages in large threads.
Back to All Threads