🚀 go-pugleaf

Objective: To do a one time read of a MAC disk with Amiga drive..

In article <1518@eklektik.UUCP>, danbabcock@eklektik.UUCP (/dev/ph1) says:
   .... Ways to read MAC disk, MAC disk organization etc deleted ....
>Of course, there is yet another method. One could design a floppy drive
>controller just like the Commodore 1541 drive, which can read and write
>at various rates. The so-called "data seperater" of the 1541 is completely
>digital and quite simple. A 16Mhz clock is an input to a programmable
>counter. Every time the counter counts down, a zero is read. A transition
>at any time is read as a one and resets the counter. Because the on-board
>CPU (a 6502) can write the countdown value to the counter chip, many data
>rates are easily supported.
    ... Stuff deleted ....
>
>-- Dan Babcock
>
>1106 Jefferson Road
>Pittsburgh, PA 15235
>(412)-373-1753

Hmmm.  Thank you Dan !!  I have came up with a simple design after reading
your article above.  Here is my proposal to a digital data separator....
 ___________       ________         ________       _______
|           | clk |        | Q0-Q5 |  COMP  |     |       | D0-D5
| 8 MHz Clk |--+--|> 6-bit |======>| A    B |<====| 6 bit |<=====  Printer
|___________|  |  | Counter|       |        |     | latch |        interface
               |  |        |       |        |     |_______|
               |  |_Reset__|       |__A=B___|
               |      ^                |
      _________V_     |                |
Raw  | Edge      |    +--->------------------------------------->  CNT
Data | detection |+> OR                |
 In  | & sync    ||   +---<-------------------------+----------->  SP
     |___________||                    |   ______   |
                  |                    |  |      |  |
                  +--------------+     +--| R  Q |--+
CLK : CLOCK                      |        |      |
COMP: Magnitude Comparator       +--------| S    |
A=B : Input A = Input B                   |______|
Sync: Synchronization circuit

The 8 MHz clock source provide a reference timing signal to this system.
The clock period is = 1/8MHz or 125 nS.  A 6 bit free running counter is
attached to the clock.  The output value is compared with the stored value
of the 6 bit latch.  If the counter value equals to the latched value, the
resulting signal is passed to the RESET input of a RS flipflop as well as
the RESET pin of the counter (via a OR gate).  The output of the FlipFlop
is = 0.  The 0 value is latched into the SP pin of the SERIAL PORT (SDR)
with the help of the reset signal as the clock.

If the input Edge detection circuit detects a transition, the RS FlipFlop
is set and the SP pin now reads a 1.  The counter is also reset via the
OR gate.

Note:  Extra clocked logics are required to avoid timing problems.

The 680X0 can change the data rate as it pleases by strobing in the 6 bit
values through the printer interface.  6-bit value provide a bit cell
of up to 7.8uS (the lower limit depends on the speed of the SDR.)  The SDR
is a synchronous serial interface in the perpherial chip.  It is available
through the printer interface.  (Its is probably use as the serial interface
for the C64 emulators.)  The SDR in this case allows us to read in the raw
data from the disk drive and grouped into 8-bit groups.  The SDR is buffered
and can be interrupt driven. (I would think the 62.5K/sec transfer rate might
justify a polling I/O approach)  The resultant raw data is dumped into a buffer
and is decoded with the help of a table....

This is what I have in mind for the variable speed data separator... It should
be able to read off almost any kind of disks.  It might even read off DS/HD
disk from a regular Amiga drive.

Note that the SDR in the output mode is limited by the 02 clock for a data rate
of 178K-bit/sec and is useless for writing to disk.  I am sure someone would
be able to fix that by hooking up a shift register off the printer port.

Well.  This is it.  I'll take a look at the project as soon as I am free after
my exams.  Anyone else is welcome to use this idea as long as I am not to be
blamed for any accidents.  If you have questions or suggestions, please send
me EMAIL.  I'll read the netnews from time to time (even during the exams),
but the local machine only keeps about 7 days or so worth.... :(

K. C. Lee

(: I do nor represent anybody nor any organizations.  The views and ideas
expressed above are either stolen or inspired by someone else.  In any
chance of an original idea, you are free to use it as long as you also
share it with others.  This message is type before an automated audiences. :)