🚀 go-pugleaf

 	it would appear to be time to post parts of 
 	a discussion that has appeared here before  ....

deskLESS.see.Z


Jan 22 11:05 1987   Page 1


 
     There is more that can be done to modify the behaviour of
 the ST desktop than appears to be gernerally  realised, so hope
that the following notes are of use.  Any  information from those 
that can shed further light would be nice.


Desktop.inf contains 
plain ascii text, and the names of installed applications can be 
edited to include path information.
There are other useful modificaions that can be made, to configure
the behaviour of the desktop.

     Recently, people have queried whether it was possible to do anything
about the action of the desktop, when displaying/printing a file.
This is particularly relevant now that LESS is available.
The few lines of desktop.inf before the application instalation 
information are :

#F FF 04   @ *.*@
#D FF 01   @ *.*@ 
#G 03 FF   *.APP@ @ 
#G 03 FF   *.PRG@ @ 
#F 03 04   *.TOS@ @ 
#P 03 04   *.TTP@ @ 

#P 03 04   d:\DUMP.TTP@ *.BAS@

The action of the desktop is clearly to try matching a 'double-clicked'
file against these templates, IN REVERSE ORDER.
Once a match has been made, the desktop then takes either the specified
action, or if none, the default action.

[ Thus if the bottom template is changed to @ *.*@ then an attempt will
be made to dump ALL files. Interestingly, not only will .prg (etc)
files not be executed, they will also not be displayed as executables
on the desktop. ]

If no other match is found, the top line wakes up the see/print
alert box that so incenses many people. 
The simple solution is just to insert the name of one's favourite
display routine, as below.  This will then ensure that any 
non-executable is then read using the facilities of LESS, (thus ending
that sinking feeling, as the crucial paragraph that one was looking for
flashes off the top of the page.)
(Printing is best handled by a proper configurable printer spooler.

#F FF 04   d:\LESS.TTP@ *.*@ 
#D FF 01   @ *.*@ 
#G 03 FF   *.APP@ @ 
#G 03 FF   *.PRG@ @ 
#F 03 04   *.TOS@ @ 
#P 03 04   *.TTP@ @ 



J.B.Webber
Physics Lab.,
University of Kent.	jbww@ukc.ac.uk






From mcvax!seismo!lll-crg!lll-lcc!vecpyr!amd!pesnta!hplabs!ucbvax!UHUPVM1.BITNET!ACS1
9 Fri May 23 13:26:25 BST 1986

In response to someones query about the desktop.inf.... tah dah -----
Everything you always wanted to know about desktop.inf, but were afraid to
ask.  Below is a typical desktop.inf file (with  a few changes added for
examples).  Below each line is a definition of what each value represents.

#a000100
This is the first desk accessory, the rs232 config.  Each 0 represents the
first column of buttons on the set rs232 config dialog box.  The first
0 is column 1 row 1, the second 0 is coumn 1 row 2, etc.  A 1 value
indicates that a button in the second column was chosen.

#b000000
This is the set printer config.  It works the same way as the rs232 config.

#c7770007000600070055200505552220770557075055507703111103
This is the color palette.  The color value is set using 3 digits at a time,
representing the red, green and blue values.  The 3111103 at the end deals
with the keyboard repeat rate, and sensitivity.  (None of the above three
will do anything if the associated desk accessory is not loaded)

#d
This is apparently reserved for a fourth accessory, and does nothing at
this time (so far as I can see).

#E C4 02   (#E=Extras)
This is two things.  The first value has to do with both the Set Preference
dialog and the mouse double click rate.  The byte is broken down as follows
with the indicated bit set performing the noted action:

Bit       7       6       5       4       3    |   2       1        0
Value    128     64      32      16       8    |   4       2        1
     displays  sorted  sorted  confirm confirm |   double click rate
       TEXT      by      by    deletes copies  |   all three bits, values
   (if not set  size    date                   |   may only be from 0-4
     displays    \       /                     |   5-7 will turn off the
      icons)     both bits                     |   mouse buttons
                  sort by
                   type

If neither bit 5 or 6 is set the sort is by name

The second value is 03 for hi rez, 02 for medium rez, or 01 for low rez.

#W 00 00 02 0B 2A 0B 08 A:\*.*@        (#W=Window)
#W 00 01 0A 01 45 09 08 A:\TEST.C\*.*@
#W 00 00 0E 09 2A 0B 08 A:\*.INF@
#W 00 00 0F 0A 2A 0B 00 @
The above four are the window defs.  The first number is how far over the
horizontal slider is, the second is the vertical slider.  The third number
is the x coordinate of the left hand side of the window (this takes on even
values, with odd values the same as next lowest even value).  The fourth
number is the y coordinate (this takes single increments).  The fifth and
sixth numbers are the width and height, respectively.  The last number
indicates where on the screen the window will open from. (The window opens
with a different shape and from a different place with each number, but when







Jan 22 11:06 1987   Page 2


you close the window, it will go to another place on the screen.  I have not
hacked at this long enuf to figure it out.)  A zero or FF will not open the
window.  The text indicates which drive's contents will be displayed.  If
the drive does not exist, the window won't open, ie. drive bits not set.
Also, if the display validation is omitted, the window won't open.
The second def above will display the contents of the folder TEST.C, while
The third def above will open a window, and only display the .INF files
on drive A.  If you close and open the window, the files will display as
defined in the file and program defs below.  (NOTE: this only applies to
icon images, every file will display in text  -- except if the file bits
are marked to be hidden, system, volume, read/write and whatever other
bits there are, in which case it won't display at all, but if it is read
only, it will display -- strange HUH?)  The bottom-most open window in
the list will be the active window.

#M 00 02 00 FF D FLOPPY DISK@ @      (#M=iMage (?))
#M 00 00 00 FF A DRIVE A@ @
#M 00 01 00 FF B FLOPPY DISK@ @
These describe the icon attributes.  The first two numbers are the column
and row position of the icon.  The column can be from 0-7, the row 0-3.
The third number determines the icon image which will be displayed.  The
image number is the same for this and the remaining defs in desktop.inf, as
follows:

0= disk drive (drawer)       1= folder (sub-directory)      2= trash can
3= executable file (.PRG, .TOS, or .TTP)   4= text (stack of papers)

The fourth value doesn't seem to do anything, but must be a place holder for
an unimplemented function.  The single letter is the drive identifier, and
the text is the drive name.  The first @ indicates the end of the drive name.
The second @ does nothing, but we can speculate as described below for the
file identifiers.  The order in the list determines the visual heirarchy
of the icons, ie. which will display on top when moved over another icon.

#T 00 03 02 FF   BLACK HOLE@ @    (#T=Trash)
This is the same as the disk drive.  If you move a disk drive identifier
below this in the list, it will display on top of the trash if moved to the
same location.  The trash has no identifier letter, but you can put one in.

#F 03 04   @ *.INF@      (#F=Files)
#D FF 01   @ *.C@        (#D=Directories)
These two determine which type of file or directory will be displayed, when
displayed as icons.  The first line will make GEM display only .INF files
for use with the SHOW, PRINT, CANCEL alert box.  If you delete this line,
no icons will be shown for any file, except as defined below for programs.
The second line does the same for sub-directories, only .C