Thread View: comp.sys.hp.hardware
2 messages
2 total messages
Started by Bill Smith
Sun, 04 Oct 1998 00:00
Memory question for Intel TC430HX
Author: Bill Smith
Date: Sun, 04 Oct 1998 00:00
Date: Sun, 04 Oct 1998 00:00
18 lines
1320 bytes
1320 bytes
Folks,
I'd like to buy a couple of 32MB SIMMs for my Intel Tucson (TC430HX)
motherboard. Looks like it supports Fast Page and EDO so I'll want to go
with EDO.
My question regards what I assume is the number of bits. Some time ago I
had bought some 16MB SIMMs which were 4X36 70ns. I'd like to add to these
if possible.
In looking for 32MB SIMMs, All I can find is 8x32. I haven't been able
to find 8x36 in EDO. Does this matter for this motherboard? Can I just get
the 8X32 60ns? Can I mix them with the other two 4x36 70ns? (I know about
pairing them in the banks & stuff).
Any advice would be appreciated.
Bill
bs@BSartist.com
Re: Memory question for Intel TC430HX
Author: Mark C.
Date: Tue, 06 Oct 1998 00:00
Date: Tue, 06 Oct 1998 00:00
52 lines
2856 bytes
2856 bytes
Bill Smith wrote: > > Folks, > I'd like to buy a couple of 32MB SIMMs for my Intel Tucson (TC430HX) > motherboard. Looks like it supports Fast Page and EDO so I'll want to go > with EDO. > > My question regards what I assume is the number of bits. Some time ago I > had bought some 16MB SIMMs which were 4X36 70ns. I'd like to add to these > if possible. > > In looking for 32MB SIMMs, All I can find is 8x32. I haven't been able > to find 8x36 in EDO. Does this matter for this motherboard? Can I just get > the 8X32 60ns? Can I mix them with the other two 4x36 70ns? (I know about > pairing them in the banks & stuff). > > Any advice would be appreciated. > > Bill > bs@BSartist.com Dear Bill: There is information on the memory requirements and the tested vendor list for the TC430HX motherboard at url: http://www.intel.com/design/motherbd/tc/tc_user.htm Here is a except from some of the information on the memory requirements, you may want to look at all the information at the url: The TC430HX provides four 72-pin SIMM sockets that make it possible to install up to 128 MB of RAM. The sockets support 1M x 32 (4 MB), 2M x 32 (8 MB), 4M x 32 (16 MB), and 8M x 32 (32 MB) single- or double-sided modules. Minimum memory size is 8 MB and maximum memory size, using four 8M x 32 SIMM modules, is 128 MB. Memory timing requires 70 ns fast page devices or, for optimum performance, 60 ns EDO DRAM. If the maximum external microprocessor clock speed is 60 MHz or slower, 70 ns EDO DRAM may be used. Parity, ECC, and non-parity memory are all supported. The four sockets are arranged in two banks of two sockets each. The sockets are designated Bank 0 and Bank 1. Each bank provides a 64/72-bit wide data path. Both SIMMs in a bank must be of the same memory size and type, although the different types of memory may differ between banks. -- Mark Intel Internet Support 100006 * trademarks of other companies are recognized as owned by their respective companies Trademarks owned by Intel may not be used without specific written permission
Thread Navigation
This is a paginated view of messages in the thread with full content displayed inline.
Messages are displayed in chronological order, with the original post highlighted in green.
Use pagination controls to navigate through all messages in large threads.
Back to All Threads