🚀 go-pugleaf

I just upgrade my motherboard to pentium motherboard but my BIOS 
is not recognise the DC5030. 
I tried to configure my BIOS and as well as the DC5030�s 
jumpers but my motherboard still won�t recognise the 
DC5030 controller. Now, I really needs your help to set-
up my AMI BIOS (P5I437 BIOS v1.2 1995-07-14) and DC5030 
controller's jumpers in order they can work together. 

This is my motherboard specification.
********************
Overview

P51437P3/I0 Green Main Board provides a highly integrated solution 
for fully compatible, high perforrnance PC/AT platforms, and 
supports Intel's Pentium microprocessor. It features Write-Back 
Secondary Cache memory for 256KB/5 12KB in size. Flexible main 
memory size can be installed from 8MB up to 128MB DRAMs, so as to 
give fully play to the advantages of the Pentium CPU The main 
board offers a wide range of interface supports for on-board IDE 
and on-board IO function integrated The current Green function 
is divided up to two phase standby and suspend

Key Features
- CPU
  = Supports Intel Pentium 75, 90,100, 120MHz CPUs
  = Supports VR and VRE CPU voltage mode
- Chipset
  = Intel's Triton chipset (include 82437, 82371, 82438)
- Main Memory
  = Supports 4x72pin SlMMs module
  = 64-bit Data Path for flexible memory size expandable from 
    8MB up to 128M DRAMs on board
  = Supports EDO/Hyper Page Mode DRAM (High speed) and also 
    supports Standard Page mode
- Cache Memory
  = Supports Write-Back Cache policy for 256KB /512KB L2 Cache
- Cache Module socket (option)
  = Supports Burst or Pipeline Burst cache module The logic 
    that supports cache module is based on Intel's COAST 
    specification
- On-board IDE
  = Supports PIO and Bus Master IDE
  = Supports up to Mode 4 Timings
  = Supports transfer rates up to 22 MBytes/s
  = Supports 2 Fast IDE interface for up to 4 IDE devices 
    providing an ulterface for IDE hard disks and CD ROMs
- Green Function
  = Supports 2 Green mode standby and suspend
- On-board I/O
  = 4 x ISA Slots and 3 x PCI Slots
= Use Winbond IO chip W83787
  = Supports up to two 3 5" or 5 25" floppy drives 360K/720K/1 
    2M/144 fonnat
  = One game port
  = All IO ports can be enabled or disabled
  = Two high speed 16550 compatible UARTs (COMI/COM3 & 
    COM2/COM4 selectable) with 16-byte send/receive FIFOs and 
    supports MIDI mode
  = One parallel port at I/O address 378H/278H/3BCH with 
    additional bi-direction I/O capability and multi-mode 
    selection (SPP/EPPIECP) (IEEE1284 compliant)
- BIOS
   = Licensed advanced AMI WinBIOS Supports Flash ROM BIOS, Plug 
	 and Play ready 
- Board Size
  = 220mm x 290rnm

Warning: Since on chip IDE controller is designed and confgured as 
a high performance bus-master, never switch pouJer off while the 
IDE hard disk is working, especially in multi-tasking operating 
systems. BIOS Configuration

*****************************************************************
Advanced Setup

System Keyboard                Present
Primary Display                VGA/EGA
Floppy Drive Seek At Boot      Disabled
System Boot Up Sequence        C, A
Password Checking              Setup
Cache Memory                   Both
System BIOS Shadow Cacheable   Enabled
Video ROM C000, 32K            Cache
Adapter ROM C800, 16K          Disabled
Adapter ROM CC00, 16K          Disabled
Adapter ROM D000, 16K          Disabled
Adapter ROM D400, 16K          Disabled
Adapter ROM D800, 16K          Disabled
Adapter ROM DC00, 16K          Disabled
Boot To PnP Operating System   No
IDE Block Mode                 Auto
....Another option..................Disable
....Another option..................Enable
On board PCI IDE               Auto
....Another option..................Disable
....Another option..................Enable
On board PCI IDE PIO Mode      Auto
On board PCI IDE 32bit Mode    Enabled
Primary Master LBA Mode        Disabled
....Another option..................Enable
Primary Slave LBA Mode         Disabled
....Another option..................Enable
Secondary Ctrl Drives Present  None
Secondary Master LBA Mode      Disabled
Secondary Slave LBA Mode       Disabled

NOTE:

  Your BIOS c01 support up to 4 Hard Disks by cllunging None 
to 2 of Number of HDDs in secondary controller
  Block Mode: Disabled If your hard disk drive supports IDE 
block transfer mode enable tllis optionforfaster IDE hard 
disk drive transfer rate.
  IDE Prim(Sec) Master (Slave) LBA Mode: Disabled LBA 
(Logical Block Addressing) mode isfor a new HDD accessing 
method to overcome the 528 Megabyte bottleneck.




BIOS Configuration
*****************************************************************
Chipset Setup

PCI Bursting..................Enabled
....Another option..................Disable
Bus concurrency...............Enabled
....Another option..................Disable
PCI Streaming.................Enabled
....Another option..................Disable
Memory Hole...................Disable
....Another option..................Disable
DRAM Speed....................60ns
8 bit I/O Recovery Time.......1 Sysclk
16 bit I/O Recovery Tirne.....1 Sysclk
PCI VGA Palette Snooping......Disabled
PCI IDE Card Selection........Absent
....Another option..................PCI Slot 1
....Another option..................PCI Slot 2
....Another option..................PCI Slot 3
....Another option..................PCI Slot 4
.PCI Prirnary IDE INT# Line....(N/A)
....Another option..................Absent
....Another option..................Not Used
....Another option..................INTA
....Another option..................INTB
....Another option..................INTC
....Another option..................INTD
  PCI Secondary IDE INT# Line...(N/A)
....Another option..................Absent
....Another option..................Not Used
....Another option..................INTA
....Another option..................INTB
....Another option..................INTC
....Another option..................INTD
IRQ3 Available to.............ISA/EISA
IRQ4 Available to.............ISA/EISA
IRQ5 Available to.............ISA/EISA
IRQ7 Available to.............ISA/EISA
IRQ9 Available to.............PCI/PnP
IRQ10 Available to............PCI/PnP
IRQII Available to............PCI/PnP
IRQ12 Available to............PCI/PnP
IRQ14 Available.to............PCI/PnP
IRQ15 Available to............PCI/PnP



*****************************************************************
Power Management Setup

Advanced Power Management..........Disabled
Full-on to Standby Time out Value .3 Min
Standby to Suspend Time out Value..3 Min
IDE Drive Power Down in............Suspend
VESA Video Power Down in...........Suspend
VESA Power Down Mode...............Off
Slow Clock Ratio...................1:1
 IRQ I Break Event.................Enabled.   
 IRQ 3 Break Event.................Enabled.   
 IRQ 4 Break Event.................Enabled.   
 IRQ 5 Break Event.................Disabled    
 IRQ 6 Break Event.................Enabled.   
 IRQ 7 Break Event.................Enabled.   
 IRQ 8 Break Event.................Disabled    
 IRQ 9 Break Event.................Disabled    
 IRQ 10 Break Event ...............Disabled    
 IRQ 11 Break Event ...............Disabled    
 IRQ 12 Break Event ...............Disabled    
 IRQ 13 Break Event ...............Disabled    
 IRQ 14 Break Event ...............Enabled.   
 IRQ 15 Break Envent...............Enabled.   
 

*****************************************************************
Peripheral Setup

Progamming Mode....................Auto
Onboard IO.........................Enabled
 Onboard FDC.......................Enabled
 Serial Portl......................3F8H
 Senal Port2.......................2F81I
 Parallel Port.....................378H
Serial Port1 MIDI Support..........Disabled
Serial Port2 MIDI Support..........Disabled
FDD A/B Exchange Function..........Disabled
Parallel Port Mode.................Normal
Parallel Extended Mode.............Disabled