🚀 go-pugleaf

RetroBBS NetNews Server

Inspired by RockSolid Light RIP Retro Guy

Article View: comp.sys.intel
Article #1221

Re: PARITY ERROR, SYSTEM HALTED ... ????

#1221
From: THOMAS LUNDQUIST
Date: Thu, 17 Dec 1992 02:20
53 lines
2798 bytes
In article <1992Dec14.090951.24678@newsserver.rrzn.uni-hannover.de> korte@alhena.itp.uni-hannover.de (Gerd Kortemeyer) writes:
>From: korte@alhena.itp.uni-hannover.de (Gerd Kortemeyer)
>
>We have got a problem with a 80286 PC, 4 MB RAM running DOS 5.0. We use
>DOS in the HIGH-mode and use only the standard HIMEM-driver.
>After about 1 minute of 'work' the system suddenly tells us
>'Parity Error, System halted' or 'Ueberlauf des internen Stapelspeichers'
>which should be something like 'Internal stack overflow'. This message
>has got nothing to do with what YOU actually do. I understand
>the first message comes from the BIOS while the second one comes from the
>operating system.
>
>When resetting the machine afterwards the computer will stop while doing
>it's memory check at some changing numbers. When switching off and then on
>again within about 10 seconds the computer will be completely death.
>
>If you wait for a few minutes, everything will again 'work' in the above
>sense. Running the BIOS-DIAGS will show no errors. Since that old computer
>has no SIMMs or SIPPs I pressed down every single memory-chip into it's
>mounting, but this had no effect, either. After all of this trial
>and error I thought it might be some virus writing perhaps into the CMOS
>which might have caused confusion even after RESET, so I initialised the
>harddisk again installing DOS 5.0 again - no effect. Strange: During the 
>whole installation things worked properly.
>
>I don't have any more ideas, does anyone else have?

This sounds like a hardware problem. The error occurs when the chips are 
warm. The installation you had might be just luck.
But Who knows when it's up to computers ??:=)

Try this : open the box, start it and work on it. When the error occurs use 
a cooling spray on the motherboard while the computer is on, reset until the 
whole thing works again. If this helps, try to locate the fault by cooling 
only some parts (memory, ASIC's, processor and so). 

But first, try to reinstall the cards, I guess some of the memory is on a 
ramcard, it might be there.

Good luck and Merry Christmas.

ThomasEZ


>
>Merry christmas
>
>Gerd
>

   ThomasEZ.

     ' I'm not perfect, but I'm perfect for you. '
Technical Details
Message-ID: <thomasez.38.724558806@dhhalden.no>
Path: arc1-ca.pugleaf.net!sparky!uunet!mcsun!sunic!aun.uninett.no!nuug!dhhalden.no!pc160.dhhalden.no!thomasez
References: <1992Dec14.090951.24678@newsserver.rrzn.uni-hannover.de>

Show Full Headers
Complete Article Headers
Newsgroups: comp.sys.intel
Path: arc1-ca.pugleaf.net!sparky!uunet!mcsun!sunic!aun.uninett.no!nuug!dhhalden.no!pc160.dhhalden.no!thomasez
From: thomasez@dhhalden.no (THOMAS LUNDQUIST)
Subject: Re: PARITY ERROR, SYSTEM HALTED ... ????
Message-ID: <thomasez.38.724558806@dhhalden.no>
Summary: Strange things happen.
Lines: 53
Sender: news@dhhalden.no (Network News User)
Nntp-Posting-Host: pc160
Organization: Ostfold College
References: <1992Dec14.090951.24678@newsserver.rrzn.uni-hannover.de>
Date: Thu, 17 Dec 1992 02:20:06 GMT