Thread View: comp.sys.sequent
3 messages
3 total messages
Started by B. Sam Blanchard
Sun, 18 Nov 1990 16:27
Request: SLIP on a Sequent S27 (info on SLIP in general)
Author: B. Sam Blanchard
Date: Sun, 18 Nov 1990 16:27
Date: Sun, 18 Nov 1990 16:27
13 lines
1115 bytes
1115 bytes
I would like to implement SLIP on a Sequent S27 running Dynix.
Dynix is 4.2bsd with many 4.3bsd enhancements. (yes, Dynix is much more)
Sequent Support told me that kernel support was required and Sequent did not
support SLIP. I do not have source.
I was told that adding 'options SLIP' might work. There appears to be an
unsupported SLIP in Sequent's Dynix. Can anyone refer me to documentation
on SLIP that would assist in using SLIP. I have "no idea" how to try SLIP out
to see if anything works.
--
B. Sam Blanchard UUCP: <backbones>!{iuvax,pur-ee}!bsu-cs!sam
ARPA: sam@bsu-cs.bsu.edu
Re: Request: SLIP on a Sequent S27 (info on SLIP in general)
Author: Ronald S H Khoo
Date: Sun, 18 Nov 1990 21:59
Date: Sun, 18 Nov 1990 21:59
24 lines
1580 bytes
1580 bytes
In article <12073@bsu-cs.bsu.edu> sam@bsu-cs.bsu.edu (B. Sam Blanchard) writes: > I would like to implement SLIP on a Sequent S27 running Dynix. > Sequent Support told me that kernel support was required and Sequent did not > support SLIP. I do not have source. If you have a spare dusty PC XT or so and can fork out the $$ for a Western Digital ethernet card (or have a PC ethernet card supported by a packet driver -- there are lots, but native support for the WD card will give you better performance) you can do this with the aid of PC route 2.1 or any other router that supports SLIP: +-------------+ ethernet +---------+ RS-232 | sequent +------------+ router +----------> SLIP! +-------------+ +---------+ The PC software is FREE by FTP from accuvax.nwu.edu under pub/pcroute. This way, you will save your sequent from being hammered by the SLIP link too. -- ronald@robobar.co.uk +44 81 991 1142 (O) +44 71 229 7741 (H)
Re: Request: SLIP on a Sequent S27 (info on SLIP in general)
Author: Tim Cook
Date: Wed, 21 Nov 1990 18:12
Date: Wed, 21 Nov 1990 18:12
21 lines
1653 bytes
1653 bytes
In article <12073@bsu-cs.bsu.edu>, sam@bsu-cs.bsu.edu (B. Sam Blanchard) writes: > I would like to implement SLIP on a Sequent S27 running Dynix. > Dynix is 4.2bsd with many 4.3bsd enhancements. (yes, Dynix is much more) There is a freely available implementation of SLIP available for DYNIX. It does need to be built into the kernel, but instructions are supplied on how to do this, and you don't need DYNIX source code. We have been using it here for about 6 months, and it works fine, except it has crashed IP about a dozen times, which I think is another symptom of the poor terminal multiplexor drivers that are found on Sequents. You may have better luck than us, but we are going to start using a PC running PCroute soon. You can find the source to this in networking/Dynix.sl.tar.Z in uunet's anonymous FTP area, or send a message to info-sslip@riacs.edu for more information. -- The above message in no way represents the official opinion, policy or standing of Victoria College, or the Computer Services department of Victoria College. If things come unstuck, they will disavow any knowledge of my actions. This item will self-destruct in five disk-accesses.
Thread Navigation
This is a paginated view of messages in the thread with full content displayed inline.
Messages are displayed in chronological order, with the original post highlighted in green.
Use pagination controls to navigate through all messages in large threads.
Back to All Threads