Thread View: comp.sys.transputer
2 messages
2 total messages
Started by Brad Banko
Fri, 28 Jun 1991 01:04
Inmos Ansi C Toolset for PC ... where is libc.lib?
Author: Brad Banko
Date: Fri, 28 Jun 1991 01:04
Date: Fri, 28 Jun 1991 01:04
25 lines
1459 bytes
1459 bytes
Hi, I have just finished installing the Inmos Ansi C Toolset on a PC host, but when I went to do the confidence testing, I had two problems: 1) the iserver which came with the Toolset can't seem to find the transputer (i have tried setting transputer=150 and transputer=#150)... the iserver which is already on the system with tds3 works ok, though. 2) (***) when I try to "ilink" the hello.c program, the linker can't find "libc.lib"... I have the isearch=c:\ictools\libs\ set ok, but there is no "libc.lib" in the libs directory? am i doing something simple wrong? thanks. (and please reply directly to me... i will get your message sooner that way.) Brad Banko -- ============================================================== Brad Banko, Theoretical Biophysics, Beckman Institute Dept of Physics, University of Illinois--Urbana-Champaign banko@lisboa.ks.uiuc.edu, (217)-244-1851, 328-4932
Re: Inmos Ansi C Toolset for PC ... libc.lib ... found!!!
Author: Brad Banko
Date: Fri, 28 Jun 1991 19:11
Date: Fri, 28 Jun 1991 19:11
45 lines
2583 bytes
2583 bytes
In article <1991Jun28.010402.15766@ux1.cso.uiuc.edu> banko@lisboa.ks.uiuc.edu (Brad Banko) writes: >Hi, > >I have just finished installing the Inmos Ansi C Toolset on a PC host, but when >I went to do the confidence testing, I had two problems: > >1) the iserver which came with the Toolset can't seem to find the >transputer (i have tried setting transputer=150 and transputer=#150)... >the iserver which is already on the system with tds3 works ok, though. > there are two versions of the iserver in ictools\iserver... one for a T4 host and one for a T8 host... you copy the one you want onto "iserver.exe", and i was trying to use the wrong one. >2) (***) when I try to "ilink" the hello.c program, the linker can't >find "libc.lib"... I have the isearch=c:\ictools\libs\ set ok, but there is >no "libc.lib" in the libs directory? > when i ran the installation the first time, i had some extra resident stuff on the system (e.g., PC_NFS...), and the PK unpacker failed with an "out of memory" error when trying to build the libc.lib (but the install kept running, so i didn't pay much attention to this)... after stripping the config.sys & autoexec.bat down to the bare essentials, (and cleaning out the old installation files!), the install ran correctly, and "libc.lib" appeared mysteriously! (or not so mysteriously.) >thanks. (and please reply directly to me... i will get your message sooner >that way.) > >Brad Banko > >-- >============================================================== >Brad Banko, Theoretical Biophysics, Beckman Institute >Dept of Physics, University of Illinois--Urbana-Champaign >banko@lisboa.ks.uiuc.edu, (217)-244-1851, 328-4932 -- ============================================================== Brad Banko, Theoretical Biophysics, Beckman Institute Dept of Physics, University of Illinois--Urbana-Champaign banko@lisboa.ks.uiuc.edu, (217)-244-1851, 328-4932
Thread Navigation
This is a paginated view of messages in the thread with full content displayed inline.
Messages are displayed in chronological order, with the original post highlighted in green.
Use pagination controls to navigate through all messages in large threads.
Back to All Threads