🚀 go-pugleaf

Does anyone here use FreeBSD and ISDN to connect to demon by any
chance ? 

I am trying to set it up but not getting any further than the
dialing part.

From demsg
-----------------------------------------------------------------
i4b-L1-timer3_expired: state = F5 Identifying Input
i4b-L1-isic_recover: HSCX B: ISTA = 0x0
i4b-L1-isic_recover:   ISAC: ISTA = 0x0
i4b-L1-isic_recover: HSCX B: IMASK = 0x0
i4b-L1-isic_recover: HSCX A: IMASK = 0x0
i4b-L1-isic_recover:   ISAC: IMASK = 0x2a
i4b-L2-i4b_T202_timeout: unit 0, N202 = 3
i4b-L1-ph_data_req: still in state F3!
i4b-L3-T303_timeout: SETUP not answered, cr = 43
i4b-L3-next_l3state: FSM illegal state, state = ST_OW - Out Wait EST,
event = EV_T303EXP - T303 timeout!
i4b-L1-timer3_expired: state = F5 Identifying Input
i4b-L1-isic_recover: HSCX B: ISTA = 0x0
i4b-L1-isic_recover:   ISAC: ISTA = 0x0
i4b-L1-isic_recover: HSCX B: IMASK = 0x0

i4b-L1-isic_recover:   ISAC: ISTA = 0x0
i4b-L1-isic_recover: HSCX B: IMASK = 0x0
i4b-L1-isic_recover: HSCX A: IMASK = 0x0
i4b-L1-isic_recover:   ISAC: IMASK = 0x2a
i4b: unit 0, assigned TEI = 74 = 0x4a
i4b: unit 0, assigned TEI = 74 = 0x4a
i4b: unit 0, assigned TEI = 74 = 0x4a

The output from isdntrace implies that it has dialed as does running isdnd
in debugging mode.

---------------------------- isdntrace ------------------------------
Q931: pd=Q.931/I.451, cr=0x40 (from origination), message=SETUP: 
     [sending complete]
     [bearer capability: 
          cap=unrestricted digital information
          std=CCITT
          rate=64 kbit/s
          mode=circuit]
     [channel id: channel=any channel (preferred)]
     [calling party number: 01226XXXXXX (type=unknown, plan=ISDN)]
     [called party number: 08450798667 (type=unknown, plan=ISDN)]

-- NT->TE - unit:0 - frame:000087 - time:24.06 12:33:06.528902 - length:4
------
------
Dump:000  00 95 01 02                                           ....
Q921: SAP=0 (Call Control), R, TEI=74, S-Frame: RR N(R) 1 PF 0 
Dump:000  00 95 01 02                                           ....
Q921: SAP=0 (Call Control), R, TEI=74, S-Frame: RR N(R) 1 PF 0 

-- NT->TE - unit:0 - frame:000088 - time:24.06 12:33:06.928907 - length:11
-----
Dump:000  02 95 00 02                                           ....
Q921: SAP=0 (Call Control), C, TEI=74, I-Frame: N(S) 0 N(R) 1 P 0 
Dump:004  08 01 c0 02 18 01 89                                  .......

--------------------------------------------------------------------------

------------------------------ isdnd  -d0xf9 -F --------------------------

isdnd[32099]: DBG msg_dialout: dial req from isp, unit 0
isdnd[32099]: DBG setup_dialout: entry I4BIP ok!
isdnd[32099]: DBG find_by_device_for_dialout: found entry 0!
isdnd[32099]: DBG FSM event [msg-dialout]: [idle => dialing]
isdnd[32099]: DBG F_DIAL: local dial out request
isdnd[32099]: DBG select_first_dialno: only one no, no = 08450798667
isdnd[32099]: CHD 00004 I4BIP rate 296 sec/unit (rate)
isdnd[32099]: CHD 00004 I4BIP dialing out from 01226XXXXXX to 08450798667
isdnd[32099]: CHD 00004 I4BIP outgoing call proceeding (ctl 0, ch 0)
isdnd[32099]: DBG msg_charging: 1 unit(s) (estimated)
isdnd[32099]: CHD 00004 I4BIP outgoing call active (ctl 0, ch 0, isp0)
isdnd[32099]: DBG FSM event [msg-con-act-ind]: [dialing => connected]
isdnd[32099]: DBG F_DOK: dial out ok
isdnd[32099]: DBG select_this_dialno: index = 0, no = 08450798667
isdnd[32099]: DBG F_DOK: dial out ok
isdnd[32099]: DBG select_this_dialno: index = 0, no = 08450798667
isdnd[32099]: DBG msg_charging: 2 unit(s) (estimated)
isdnd[32099]: DBG msg_charging: 3 unit(s) (estimated)
isdnd[32099]: CHD 00004 I4BIP outgoing call disconnected (remote)
isdnd[32099]: CHD 00004 I4BIP cause 16: Normal call clearing (Q.850)
isdnd[32099]: CHD 00004 I4BIP charging: 3 units, 601 seconds
isdnd[32099]: CHD 00004 I4BIP accounting: in 621625, out 414423 (in
620977, out