🚀 go-pugleaf

       ___________________________________________________    
      |                  CALL FOR PAPERS                  |
      |         ASME Design Automation Conference         |
      |   Albuquerque, New Mexico - September 19-22, 1993 |
      |___________________________________________________|


The approaching 50th anniversary of the ASME Design Division gives
us an opportunity to reflect on the importance of the practice of
engineering design and design research. In an effort to foster
the ongoing development of design research, the ASME Design Automation	
Committee strongly encourages suggestions, ideas and participation
from the world-wide engineering design community including those
in academia, industry, government agencies and national labs.
Special subcommittees have been formed to address new research
areas at the conference.

Technical areas of interest for paper submissions are listed below. 
Papers in other design areas are also welcome. All papers should
be submitted (by submission dates listed below) ONLY to the conference
chairman, and the papers review chairman and co-chairman, as follows:

Prof. Brian J. Gilmore (conference chairman)
Dept. of Mech. Eng. - Room 208 
Penn State University
University Park, Pa 16802
Ph.: (814)863-0736, Fax: (814)863-4848
email: bjg@mevax.psu.edu
* Simulation & analysis of mechanical systems
* Design of experiments for products and processes
* Design for X (X=manufacturability, assembly, recycleability, etc.)
* Concurrent & life-cycle engineering
* Theory & application of finite elements in design

Dr. David A. Hoeltzel (paper review chairman)
Pitney Bowes Corporation
Research & Advanced Concepts
35 Waterview Drive
Shelton, Ct 06484-8000
Ph.: (203)924-3026, Fax: (203)924-3523
email: hoeltzel@pb.com
* Geometric modeling, parametric & variational geometry, features
* Tolerance analysis
* Artificial intelligence, knowledge-based systems, and smart 
   mechanics in design
* Computer-aided design & computer graphics
* Object-oriented design & analysis

Prof. Shapour Azarm (paper review co-chairman & foreign papers 
                     review chairman)
Dept. of Mech. Eng.
University of Maryland
College Park, Md 20742
Ph.: (301)405-5250, Fax: (301)314-9477
email: azarm@eng.umd.edu
* design optimization (theory & applications)
           
          
*************PAPER SUBMISSION DATES AND PUBLICATION*************

Submit 5 copies of each paper:
January 1, 1993 for papers outside North America (send to Prof. Azarm)
January 29, 1993 for papers from North America (send to Prof. Gilmore,
   Dr. Hoeltzel, or Prof. Azarm, depending on topic area)
 
Notification to authors:
April 15, 1993
 
Final papers in camera-ready form (pre-shrunk or full-size mats):
May 15, 1993
 
All papers will be reviewed for publication in a bound proceedings 
volume.
 
Authors wishing their papers to be considered for publication in the 
ASME Journal of Mechanical Design, must submit copies of their papers
separately to the Editor.

*************        CONFERENCE INFORMATION        *************	

In addition to the topic areas outlined above, suggestion for special
session topics or inquiries related to the conference should be
made to: Prof. Brian J. Gilmore, at the above address.
          
Finally, it is suggested (not required) that authors wishing to 
submit a paper in the following areas discuss their ideas with the 
technical subcommittee chairpersons listed below.

Prof. Jami Shah (Tolerance Subcommittee)
Dept. of Mech. Eng.
Arizona State Univ.
Tempe, Arizona 85287-6106
ph.: (602)965-6145
email:jshah@enuvax.eas.asu.edu
* Features in geometric modeling
* Parametric & variational geometry
* Geometric tolerancing

Prof. Josh Turner (Tolerance subcommittee)
Rensselaer Design Research Center
Rensselaer Polytechnique Institute
Troy, New York 12180-3590
Ph.: (518)276-6751, Fax: (518)276-2702
email: jturner@geos.rdrc.rpi.edu
* Tolerance synthesis, analysis and modeling, geometric tolerancing,
  assembly modeling

Prof. Kos Ishii (Concurrent engineering subcommittee)
Dept. of Mech. Eng.
Ohio State Univ.
Columbus, Ohio 43210-1107
Ph.: (614)292-8486, Fax: (614)292-3163
email: ishii.2@osu.edu
* Life-cycle engineering design, simultaneous design of products
   and Processes
* Design for X (X=manufacture, service, recycling, etc.)
* Design of experiments in product & process optimization

Prof. Panos Papalambros (Design optimization subcommittee)
Dept. of Mech. Eng. & Applied Mech.
Univ. of Michigan
Ann Arbor, Michigan 48109-2125
email: papalambros@um.cc.umich.edu
* Optimization theory & applications

Prof. Dr.-Ing. Hans Eschenauer (Design optimization subcommittee)
Institute of Mechanics & Control Eng.
Univ. of Siegen
5900 Siegen, Germany
email: weinert@imr-sun1.fb5.uni-siegen.de
* Optimization theory & applications

Profs. Mark Ganter & Duane Storti (Geometric modeling subcommittee)
Dept. of Mech. Eng.
Univ. of Washington
Seattle, WA 98195
email: ganter@puff.me.washington.edu

* Topology issues and representations in geometric modeling
* Blending, sweeping, joining and offset in geometric modeling