🚀 go-pugleaf

try Revolve at the tip


"Bob Parker" <bobp.deletethis@bluebottle.com> wrote in message
news:t67ih25hirn1v1lrlrhluavisgbfe1l891@4ax.com...
> Hi again,
>    Sorry if this seems to be slightly off-topic. I'm looking for an
> output paper feed roller drive gear for my Laserjet 1020. HP won't
> supply it on its own.
>    As far as I can tell, the 1000 series Laserjets all use the same
> gear. There's a photo of it at
> http://members.ozemail.com.au/~bobpar/roller%20gear.jpg
>    If you have a scrapped printer and would like to sell me that gear,
> please let me know.
>  Thanks. :-)
>
> Bob

"Bob Parker" <bobp.deletethis@bluebottle.com> wrote in message 
news:t67ih25hirn1v1lrlrhluavisgbfe1l891@4ax.com...
> Hi again,
>   Sorry if this seems to be slightly off-topic. I'm looking for an
> output paper feed roller drive gear for my Laserjet 1020. HP won't
> supply it on its own.
>   As far as I can tell, the 1000 series Laserjets all use the same
> gear. There's a photo of it at
> http://members.ozemail.com.au/~bobpar/roller%20gear.jpg
>   If you have a scrapped printer and would like to sell me that gear,
> please let me know.
> Thanks. :-)

What on earth are you doing? That printer is trashed now that 0.01c worth of 
plastic is broken off. Throw it away immediately. How are HP going to make 
an income if you keep repairing their printers?

Michael

PS. I bet they did everything they could to make it difficult to repair. :-) 

On Tue, 26 Sep 2006 23:48:43 +1000, "Michael C" <nospam@nospam.com>
wrote:
>
>What on earth are you doing? That printer is trashed now that 0.01c worth of 
>plastic is broken off. Throw it away immediately. How are HP going to make 
>an income if you keep repairing their printers?
>
>Michael
>
>PS. I bet they did everything they could to make it difficult to repair. :-) 


    I actually found a service manual on the net which was pretty good
at explaining how to take it apart.
    Of course you can't buy many individual parts for it, only
complete sub-assemblies and things like the output document holder.
    I wasn't surprised to see lots of references to the effect of "If
this part is broken, replace the printer".
   

Bob

Bob Parker wrote:
> Hi again,
>    Sorry if this seems to be slightly off-topic. I'm looking for an
> output paper feed roller drive gear for my Laserjet 1020. HP won't
> supply it on its own.
>    As far as I can tell, the 1000 series Laserjets all use the same
> gear. There's a photo of it at
> http://members.ozemail.com.au/~bobpar/roller%20gear.jpg
>    If you have a scrapped printer and would like to sell me that gear,
> please let me know.
>  Thanks. :-)
> 
> Bob
> 
I have a junked 3200m all-in-one.  This uses the same engine as the 1100....

jak

On Tue, 26 Sep 2006 12:02:36 -0500, jakdedert
<jakdedert@bellsouth.net> wrote:
>
>I have a junked 3200m all-in-one.  This uses the same engine as the 1100....
>
>jak

   I've been looking, but can't find a detailed drawing of the fuser
output rollers on that model. The gear I need has 14 teeth....

Bob

Bob Parker wrote:
> On Tue, 26 Sep 2006 12:02:36 -0500, jakdedert
> <jakdedert@bellsouth.net> wrote:
>> I have a junked 3200m all-in-one.  This uses the same engine as the 1100....
>>
>> jak
> 
>    I've been looking, but can't find a detailed drawing of the fuser
> output rollers on that model. The gear I need has 14 teeth....
> 
Sorry, it's not 'that' junked.  I bought one on eBay because this one 
had a dud modem board; so I've not dug into the mechanicals.

Funny...turned out the eBay one was easier to fix, so this one still sits.

jak
> Bob
> 
> 
> 

Hi!

Good luck finding the part.

I have at least one DeskJet 5850 that's only good as a locally connected
printer after a firmware upgrade that went wrong. Apparently the internal
J6077a JetDirect isn't actually upgradeable or the firmware is bad. Either
way, HP has never commented, doesn't sell the (removable once you get the
printer apart) JetDirect module, or offered to fix this problem.

If you can't find a replacement gear, you might try making and installing a
new tooth. There's information in the FAQ about doing this.

William

"Bob Parker" <bobp.deletethis@bluebottle.com> wrote in message 
news:t67ih25hirn1v1lrlrhluavisgbfe1l891@4ax.com...
> Hi again,
>   Sorry if this seems to be slightly off-topic. I'm looking for an
> output paper feed roller drive gear for my Laserjet 1020. HP won't
> supply it on its own.
>   As far as I can tell, the 1000 series Laserjets all use the same
> gear. There's a photo of it at
> http://members.ozemail.com.au/~bobpar/roller%20gear.jpg
>   If you have a scrapped printer and would like to sell me that gear,
> please let me know.
> Thanks. :-)
>
> Bob

I have just sold a broken LJ1022 on eBay, got a whole $23.50 for it!.  Try 
eBay..    Colin