🚀 go-pugleaf

Hi All

	I just install RedHat 3.0.3 on my system, I always received this error
message when I type startx command

Script started on Sun Apr 13 12:44:57 1997
[root@linux /root]# startx

XFree86 Version 3.2A / X Window System
(protocol Version 11, revision 0, vendor release 6300)
Release Date: Jan 28 1997
	If the server is older than 6-12 months, or if your card is newer than
the above date, look for a newer version before reporting
problems.  (see http://www.XFree86.Org/FAQ)
Operating System: Linux 2.0.28 i586 [ELF] 
Configured drivers:
  ET4000W32: accelerated server for ET4000W32 graphics adaptors
(Patchlevel 0):
      et4000w32, et4000w32i, et4000w32p_rev_a, et4000w32i_rev_b,
      et4000w32i_rev_c, et4000w32p_rev_b, et4000w32p_rev_c,
      et4000w32p_rev_d, et6000
(using VT number 7)

XF86Config: /usr/X11R6/lib/X11/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) Mouse: type: Microsoft, device: /dev/tty00, baudrate: 1200
(**) ET4000W32: Graphics device ID: "TrueSpeed"
(**) ET4000W32: Monitor ID: "MPR II Monitor"
(--) ET4000W32: Mode "1024x768" needs hsync freq of 56.48 kHz. Deleted.
(--) ET4000W32: Mode "1280x1024" needs hsync freq of 51.02 kHz. Deleted.
(--) ET4000W32: Mode "1024x768" needs hsync freq of 62.50 kHz. Deleted.
(--) ET4000W32: Mode "1280x1024" needs hsync freq of 64.25 kHz. Deleted.
(--) ET4000W32: Mode "1280x1024" needs hsync freq of 78.86 kHz. Deleted.
(--) ET4000W32: Mode "1280x1024" needs hsync freq of 81.13 kHz. Deleted.
(--) ET4000W32: Invalid vertical timing for mode "400x300". Deleted.
(**) FontPath set to
"/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/Type1/,/usr/X11R6/lib/X11/fonts/Speedo/,/usr/X11R6/lib/X11/fonts/75dpi/,/usr/X11R6/lib/X11/fonts/100dpi/"
(--) ET4000W32: PCI: Tseng Labs ET6000 rev 48, Memory @ 0xe0000000, I/O
@ 0x6000
(--) ET4000W32: ET6000: CLKDAC ID: 0x84
(--) ET4000W32: ET6000: Using built-in 135 MHz programmable Clock
Chip/RAMDAC
(--) ET4000W32: ET6000: Detected 2560 kb of multi-bank DRAM
(--) ET4000W32: ET6000: MClk: 91.87 MHz
(--) ET4000W32: chipset:  et6000
(--) ET4000W32: videoram: 2559k
(--) ET4000W32: Ramdac speed: 135
(**) ET4000W32: Using ET6000 built-in programmable clock
(--) ET4000W32: Maximum allowed dot-clock: 135.000 MHz
(**) ET4000W32: Mode "1024x768": mode clock =  65.000
(**) ET4000W32: Mode "800x600": mode clock =  50.000
(**) ET4000W32: Mode "640x480": mode clock =  31.500
(**) ET4000W32: Virtual resolution set to 1280x1024
PEX extension module not loaded
XIE extension module not loaded
error opening security policy file
/usr/X11R6/lib/X11/xserver/SecurityPolicy
sh: /usr/X11R6/lib/X11/xkb/xkbcomp: No such file or directory
Couldn't load XKB keymap, falling back to pre-XKB keymap

Fatal server error:
Cannot open mouse (No such file or directory)

When reporting a problem related to a server crash, please send
the full server output, not just the last messages

xinit:  unexpected signal 13

[root@linux /root]# exit
Script done on Sun Apr 13 12:45:14 1997


	My VGA card is ET6000 with 2.25M ram, Linux partition have about 300M,
Linux Swap partition have about 30M, My system is P133 with 32M RAM. My
XFree86 is 3.2a version.

Can any one HELP me please :(

Thank's

-- 
�����y�H  Leo TANG :)
you can send me a E-mail in following address :)
mailto:mktan4@cfs02.cc.monash.edu.au
mailto:mktan4@nellads.cc.monash.edu.au
mailto:mktan4@silas.cc.monash.edu.au
mailto:mtan1@bedrock.eng.monash.edu.au
mailto:mktan@yoyo.cc.monash.edu.au