🚀 go-pugleaf

In article <1992Oct28.174438.266@logica.co.uk>, system@logica.co.uk writes:
> OPEN QUESTIONS TO ALL NEWS READERS
> 
> 1.
> If you have just added 32mb memory to a 32mb memory machine (VAX4300) what 
> would be the main parameters changes to be made, apart from Working Sets and 
> why.

Just run autogen, it really does a pretty good job with adding memory (it DOES
get confused when you remove it).

> 
> 2.
> Using what tools could you show a need for more processor power on a 6310.

Use MONITOR.  If you're COMPUTE bound you could argue for another processor,
but remember that more processors won't help IO bound systems.

> 
> 3.
> Does anyone know the full table of classes for OPC$OPA0_CLASSES as the
> manual is not available.
> 

Do a REPLY/ENABLE and you should see the entire list.  I believe HELP REPLY
will also, eventually, let you figure out all the available operator classes.
-- 
Dick Munroe				Internet: munroe@dmc.com
Doyle Munroe Consultants, Inc.		UUCP: ...uunet!thehulk!munroe
267 Cox St.				Office: (508) 568-1618
Hudson, Ma.				FAX: (508) 562-1133

GET CONNECTED!!! Send mail to info@dmc.com to find out about DMConnection.

In article <1992Oct28.174438.266@logica.co.uk>, system@logica.co.uk writes:
> OPEN QUESTIONS TO ALL NEWS READERS
> 
> 3.
> Does anyone know the full table of classes for OPC$OPA0_CLASSES as the
> manual is not available.
	Here is the standard listing out of sylogicals.template
$!
$! The state of the operator on OPA0:, and the state of the operator logfile,
$! can be controlled by defining logical names here in SYLOGICALS.COM.  Any
$! commands to enable or disable operator classes in other system startup
$! procedures should be removed, and the appropriate logical names defined here.
$!
$! By default, the operator states are:
$!
$!	For all systems except workstations in a VAXcluster:
$!
$!		OPA0: is enabled for all classes.
$!		The log file SYS$MANAGER:OPERATOR.LOG is opened for all classes.
$!
$!	For workstations in a VAXcluster:
$!
$!		OPA0: is not enabled.*
$!		No log file is opened.
$!
$!		 * OPA0: will be also be SET TERMINAL/PERMANENT/NOBROADCAST
$!
$! To override the default enabled classes, define the following /SYSTEM
$! logical names.
$!
$!	OPC$OPA0_ENABLE
$!
$!		If defined to be true, then OPA0: is enabled as an operator.  If
$!		defined to be false, then OPA0: is not enabled as an operator.
$!
$!	OPC$OPA0_CLASSES
$!
$!		This logical defines the operator classes to be enabled on
$!		OPA0:.  The logical can be a search list of the allowed	
$!		classes, a list of classes, or a combination of the two, for
$!		example: 
$!
$!			$ DEFINE /SYSTEM OPC$OPA0_CLASSES CENTRAL,DISKS,TAPE 
$!			$ DEFINE /SYSTEM OPC$OPA0_CLASSES "CENTRAL,DISKS,TAPE" 
$!			$ DEFINE /SYSTEM OPC$OPA0_CLASSES "CENTRAL,DISKS",TAPE 
$!
$!	Note that OPC$OPA0_CLASSES can be defined even if OPC$OPA0_ENABLE is
$!	not defined.  In that case, the classes are used for any operators
$!	that are enabled, but the default is used to determine whether or not
$!	to enable the operator.
$!
$!	OPC$LOGFILE_ENABLE
$!
$!		If defined to be true, then an operator log file is opened.
$!		If defined to be false, then no log file is opened.
$!
$!	OPC$LOGFILE_CLASSES
$!
$!		This logical defines the operator classes to be enabled for
$!		the log file.  The logical can be a search list of the allowed
$!		classes, a comma-separated list, or a combination of the two.
$!		OPC$LOGFILE_CLASSES can be defined even if OPC$LOGFILE_ENABLE
$!		is not defined.
$!
$!	OPC$LOGFILE_NAME
$!
$!		This logical supplies information to be used in conjunction
$!		with the default name SYS$MANAGER:OPERATOR.LOG to define the
$!		name of the log file.  If the log file is directed to a disk
$!		other than the system disk, commands to mount that disk should
$!		be included in the command procedure SYLOGICALS.COM.  This
$!		logfile name will be used whenever a logfile is recreated.
$!
$!	Note that only OPC$LOGFILE_NAME is used for more than the initial
$!	startup of OPCOM.  For example, issuing the command REPLY/LOG will
$!	open a new file with the specified name and with all classes enabled
$!	(OPC$LOGFILE_ENABLE and OPC$LOGFILE_CLASSES are ignored).	
$!
$!  The list of all operator classes is:
$!
$!	CENTRAL,PRINTER,TAPES,DISKS,DEVICES,CARDS,NETWORK,CLUSTER,
$!	SECURITY,LICENSE,OPER1,OPER2,OPER3,OPER4,OPER5,OPER6,
$!	OPER7,OPER8,OPER9,OPER10,OPER11,OPER12
$!
$!  Operator classes can be redefined via logical names.  For example, a site
$!  could decide that the site-specific operator OPER1 should be known as
$!  operator class SYSTEM_MANAGER.  This would be done via:
$!
$!		$ DEFINE /SYSTEM  SYSTEM_MANAGER  OPER1
$!
$!  Thereafter, the system manager could do a REPLY/ENABLE=SYSTEM_MANAGER,
$!  users could do REQUEST /TO=SYSTEM_MANAGER, etc.
$!
$!
			...rew
-- 
-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   Richard Wiseman		 VAX-VMS Crafts Person
   MONSANTO	                Internet:  Rewise@musctn.monsanto.com
   RR #5 Wiggins Rd.             Yellnet:  +1 (319)262-7528 or 262-7339
   BOX 473                           FAX:  +1 (319)262-5626
   Muscatine, Ia 52761        Disclaimer:  All opinions are my own, I think
-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+