🚀 go-pugleaf

" Doug Bashford " <see.my.sig@theBeach.edu> wrote in message
news:3bd4647f.80698265@news.psnw.com...
>
>
>  On Wed, 17 Oct 2001, "Hooda Gest" wrote about:
>  Re: No solution??? Re: Still none: Re: I lost my Dial-up sounds
>
>
> >
> >After reading this, I find I don't quite grasp the problem...
>
> No modem sound, no beep beep buzz ka-chang sounds when
> connecting.  All other sounds (except "drums") seem ok.

The drums are part of Windows but I don't recall if that image has sound
accompanying it. I only see that image during installation processes. Let's
concentrate on the modem sounds.

All my comments are predicated on the premise that there was never any time
that the modem sounds were audible.

> >Volume and sound control for a modem on a dialup is controlled through
the
> >DUN connection icon's properties. You access the modem configuration
through
> >that and change the sound. Changing sound under Control Panel/Modems will
> >have no effect since the DUN settings will override it.
> >
> >Check your modem log to see what is being sent to the modem in regards to
Mx
> >and Lx.
>
> Thanks Hooda!  I don't see any problems, do you?
>
> 10-22-2001 11:03:32.69 - HSP56 MicroModem in use.
> 10-22-2001 11:03:32.70 - Modem type: HSP56 MicroModem
> 10-22-2001 11:03:32.70 - Modem inf path: PCTEL_~1.INF
> 10-22-2001 11:03:32.70 - Modem inf section: Modem4
> 10-22-2001 11:03:34.55 - 115200,N,8,1
> 10-22-2001 11:03:34.77 - 115200,N,8,1
> 10-22-2001 11:03:34.80 - Initializing modem.
> 10-22-2001 11:03:34.80 - Send: AT<cr>
> 10-22-2001 11:03:34.80 - Recv: AT<cr>
> 10-22-2001 11:03:34.81 - Recv: <cr><lf>OK<cr><lf>
> 10-22-2001 11:03:34.81 - Interpreted response: Ok
> 10-22-2001 11:03:34.81 - Send: AT&FE0&C1&D2&K3V1W3S0=0<cr>
> 10-22-2001 11:03:34.81 - Recv: AT&FE0&C1&D2&K3V1W3S0=0<cr>
> 10-22-2001 11:03:34.81 - Recv: <cr><lf>OK<cr><lf>
> 10-22-2001 11:03:34.81 - Interpreted response: Ok
> 10-22-2001 11:03:34.81 - Send: ATS7=60S30=0M1\N3%C3&K3B0N1X4<cr>
> 10-22-2001 11:03:34.82 - Recv: <cr><lf>OK<cr><lf>
> 10-22-2001 11:03:34.82 - Interpreted response: Ok
> 10-22-2001 11:03:34.82 - Send: At S11=55 M1 L3<cr>
> 10-22-2001 11:03:34.82 - Recv: <cr><lf>OK<cr><lf>
> 10-22-2001 11:03:34.82 - Interpreted response: Ok
> 10-22-2001 11:03:34.83 - Dialing.
>
>
> The At S11=55 M1 L3 I added via the DUN icon.
> At S11=55 has been there forever, and functions.
> The others I added after this problem.  Also,
> the volume "slider switch" there is set to max.

Everything looks good.

> > Also, if this is a voice modem, check your cabling between sound
> >card and modem.
>
> My Celeron has no sound card, no modem card.
> It seems to work ok, I commonly get 53333 connects.
> --Doug

The sound, of course, is not essential to the operation. It just lets you
know the progress of the negotiations between the modem. You have a modem
that is either imbedded in the  motherboard or is plugged into the AMR slot.
Your sound functions are also imbedded in the MB and there may be a need for
a jumper on the MB to transfer the sound.

You might want to contact the vendor for the system, if you still can. Or,
if you have the manual for the motherboard, there could be some useful info
there.


--
Hooda Gest
"In a New York minute, everything can change..."