🚀 go-pugleaf

try a recent kernel, 2.0.36pre or 2.1.126
2.0.30 gives lots of errors and 2.1.48 is way too old

Marc


Fco Javier Pulido Vaquero wrote in message
<71l8jg$r21$1@diana.bcn.ibernet.es>...
>Who can help me?
>
>e-mail : fjpulido@lobocom.es
>
>- Boot Warning (Only boots sometimes if I use Loadlin with LINUX
>                             KERNEL 2.0.30/2.0.34/2.1.48):
>
>  Probing PCI hardware
>  Unknown PCI device
>  PCI Device id=8A01
>  PCI Device id=7100
>  PCI Device id=7110
>
>- Sometimes the system emits the following message (kernel 2.0.39 -
Example)
>:
>
>booting ....
>(.......)
>Starting additional networking services:.
>double fault:0000
>CPU: 0
>EIP: 0010:[<001097F2>]
>EFLAGS: 00010246
>EAX: 7EFFE0C7  EBX: 0000096C  ECX: FFFFFC18  EDX: 00221DBC
>ESI: 002215E8  EDI: 00000000  EBP: 00000912  ESP: 00221598
>DS: 0018  ES:0018  FS: 002B  GS:0018  SS:0018
>
>Process swapper (pid:0 , process nr=0, stackpage=0021f60c)
>Stack: 00109847 00221DBC 0010A81D 00000100 0010946C 0000001E 002215E8
>00000000
>        00000912 FFFFFFDA 00000018 00000018 00000018 00000018 00000070
>00109033
>        00000010 00000246 00109227 00000000 68747541 000994C1 00101FFC
>00000000
>Call Trace: [<00109847>] [<0010a81d>] [<0010946c>] [<00109227>]
>[<00116f94>]
>             [<00111848>]
>Code: f4 83 3d f8 f5 21 00 00 75 0e e8 17 7e 00 00 83 3d f8 f5 21
>kfree of non-kmalloced memory: 00221854, next=00000000, order=0
>kfree of non-kmalloced memory: 00221644, next=00000000, order=0
>kfree of non-kmalloced memory: 00221b58, next=00000000, order=0
>idle task may not sleep
>
>- FILE /proc/pci
>  *****************
>
>PCI devices found:
>  Bus  0, device   9, function  0:
>    VGA compatible controller: S3 Inc. Unknown device (rev 1).
>      Vendor id=5333. Device id=8a01.
>      Medium devsel.  IRQ 10.  Master Capable.  Latency=64.  Min Gnt=4.Max
>Lat=255.
>      Non-prefetchable 32 bit memory at 0xf8000000.
>  Bus  0, device   7, function  3:
>    Bridge: Intel Unknown device (rev 1).
>      Vendor id=8086. Device id=7113.
>      Medium devsel.  Fast back-to-back capable.
>  Bus  0, device   7, function  2:
>    USB Controller: Intel Unknown device (rev 1).
>      Vendor id=8086. Device id=7112.
>      Medium devsel.  Fast back-to-back capable.  IRQ 11.  Master Capable.
>Latency=64.
>      I/O at 0xdf80.
>  Bus  0, device   7, function  1:
>    IDE interface: Intel Unknown device (rev 1).
>      Vendor id=8086. Device id=7111.
>      Medium devsel.  Fast back-to-back capable.  Master Capable.
>Latency=32.
>      I/O at 0xffa0.
>  Bus  0, device   7, function  0:
>    ISA bridge: Intel Unknown device (rev 1).
>      Vendor id=8086. Device id=7110.
>      Medium devsel.  Fast back-to-back capable.  Master Capable.  No
>bursts.
>  Bus  0, device   0, function  0:
>    Host bridge: Intel Unknown device (rev 1).
>      Vendor id=8086. Device id=7100.
>      Medium devsel.  Master Capable.  Latency=32.
>
>
>- FILE /proc/Meminfo (128 Mbytes RAM)
>  **********************************************
>        total:    used:    free:  shared: buffers:  cached:
>Mem:  65294336 32698368 32595968  4386816 24461312  3866624
>Swap: 16510976        0 16510976
>MemTotal:     63764 kB
>MemFree:      31832 kB
>MemShared:     4284 kB
>Buffers:      23888 kB
>Cached:        3776 kB
>SwapTotal:    16124 kB
>SwapFree:     16124 kB
>
>
>- Mainboard features:
>
>- Processor: AMD K6-2 300 Mhz
>- RAM: SDRAM 128 Mbytes (2 modules DIMM 64 Mbytes)
>- Intel i430TX PCI chipset
>- Supports Pentium 75-300 Mhz CPUs with ZIF socket, including
>    Pentium P54C and P55C (MMX), Cyrix/IBM 6X86/6x86L/6x86MX (M2),
>    IDT C6, and AMD K5/K6 CPUs.
>- Chipset (Socket 7, intel 82371AB, intel 82439TX)
>- Provides CPU Plug & Play (Auto Voltage/Frequency/Bus Frequency
>    Ratio) techniques for faster and eaiser CPU installation.
>- Provides auto switching power 2.0V to 3.5V for CPU core voltage.
>- Supports 64M-bit (16Mx4,8Mx8,4Mx16) DRAM/SDRAM technology.
>- Provides 4x72-pin SIMM modules auto banking in multiple configu-
>   ration up to 256MB and also, 2 x 168-pin DIMM to support SDRAM/EDO
>   DRAM/Page Mode DRAM up to 256MB.
>- Supports onboard 512KB Pipelined Burst synchronous L2 cache.
>- Supports Ultra DMA/33 and ACPI.
>- Provides dual ATX (20-pin) and AT (12-pin) power conectors and
>   ATX power supports Suspend Switch, Power Button, Wake On LAN, and
>   Alarm Wake Up.
>- 4 PCI Local Bus slots and 3x16 bits ISA Bus slots.
>- PCI IDE Controller supports PIO Mode 0 to Mode 4,Ultra DMA/33 at
>    maximun transfer rate of 33 MB/s, and Bus Master IDE DMA Mode 2
>- Supports PS/2 Mouse conector and pin header.
>- Supports 2.88MB, Iomega ZIP-100M, and IDE LS-120 FDD;bootable from
>    floppy, HDD, CDROM, SCSI, NetWork, LS-120,ZIP, or others.
>- Onboard super Multi-I/O chip supports 2 serial ports with 16550 fast
>    UART compatible, 1 parallel port with EPP and ECP capabilities, and
>    one floppy disk drive interface with 1 MB/s data transfer rate.
>- Supports ATX FORM CARD containing PS/2 mouse, 2 USB interface, and
>    Infrared conectors (optional)
>- Onboard PCI Bus Master IDE interface supports 4 IDE devices with 2
>   channels; BIOS supports 4 IDE harddisk drives which do not need
>   device driver for S/W application and the capacity of each harddisk
>   can be larger than 528MB AND UP TO 8.5GB.
>- Sound Blaster 16/PRO compatible with stereo onboard.
>
>
>
>

Fco Javier Pulido Vaquero wrote:
> 
> Who can help me?
> 
> e-mail : fjpulido@lobocom.es
> 
> - Boot Warning (Only boots sometimes if I use Loadlin with LINUX
>                              KERNEL 2.0.30/2.0.34/2.1.48):
> 
>   Probing PCI hardware
>   Unknown PCI device
>   PCI Device id=8A01
>   PCI Device id=7100
>   PCI Device id=7110
> 
--cutting--
> - Processor: AMD K6-2 300 Mhz
> - RAM: SDRAM 128 Mbytes (2 modules DIMM 64 Mbytes)
> - Intel i430TX PCI chipset
> - Supports Pentium 75-300 Mhz CPUs with ZIF socket, including
>     Pentium P54C and P55C (MMX), Cyrix/IBM 6X86/6x86L/6x86MX (M2),
>     IDT C6, and AMD K5/K6 CPUs.
> - Chipset (Socket 7, intel 82371AB, intel 82439TX)
--cutting
> - Sound Blaster 16/PRO compatible with stereo onboard.
Using the same Chipset. I suppose that the linuxkernel can't identify
the Intel PCI-Bridges and PCI-IDE-Bridges: In general, all the stuff
from Intel on-board. When I bought the motherboard, an additional floppy
whith devicedrivers for that PCI-IDE-Bridges from Intel was supplied for
NT and Windows. There, I've found the same problem: Unknown device. So,
while I'm usint kernel 2.0.30, all I've got while booting would be the
message 'unknown pci-device'.

SAM
-- 
-------------------------------
  Even paranoids have enemies
           
                -ANONYMOUS-
-------------------------------

>Fco Javier Pulido Vaquero wrote:

>> Who can help me?

>> - Processor: AMD K6-2 300 Mhz
>> - RAM: SDRAM 128 Mbytes (2 modules DIMM 64 Mbytes)
>> - Intel i430TX PCI chipset
>> - Supports Pentium 75-300 Mhz CPUs with ZIF socket, including
>>     Pentium P54C and P55C (MMX), Cyrix/IBM 6X86/6x86L/6x86MX (M2),
>>     IDT C6, and AMD K5/K6 CPUs.
>> - Chipset (Socket 7, intel 82371AB, intel 82439TX)

Whups.  Just noticed something which may or may not be significant.

The K6-2-300 CPU requires a 2.2-volt core voltage supply.  This
voltage may or may not be available on your motherboard - I can't tell
based on what you report.  The K5 CPUs use 3.4 volts, while the K6
uses 3.2 volts (K6-PR233), 2.9 volts (K6-166, K6-200), or 2.2 volts
(K6-233, -266, and -300).

Since your note doesn't say specifically that the K6-2 is supported by
the motherboard, I suspect that there's a chance that the MB might not
have a 2.2-volt dual-plane power supply.  If this is the case, and if
you've set the voltage-regulator jumpers based on the documentation
for an older K6 processor, you may very well be running your K6-2 at a
higher voltage than it is rated for.  This might result in
overheating, intermittent operation, crashes, chip failure or damage,
and/or the collapse of the economy of a major Asian country.

You might want to check the AMD web site and confirm that your
motherboard is on their "supported" list.  If it isn't, you may need
to either switch processors, or switch motherboards (FWIW, I like my
ASUS P5A with the K6-2-300).

-- 
Dave Platt                                        dplatt@feghoot.ml.org
Visit the Jade Warrior home page:   http://feghoot.ml.org/jade-warrior/
  I do _not_ wish to receive unsolicited commercial email, and I will
     boycott any company which has the gall to send me such ads!