🚀 go-pugleaf

Venex wrote:
> 
> Kurniadi Asrigo <q8n25@unb.ca> wrote:
> >(...) I guess
> >there is only one problem now. I don't know why in the booting prosess,
> >it's looking for sb.o modules and it can not find it. I compiled it as
> >module but why it can not find it? How do I configure it and make it
> >working again? Is there old init.script that i have to change or erase
> >to reset it and start the installation again?
> 
> Did you do: "make dep" before compiling the kernel and "make modules" and "make
> modules_install" afterwards?

Yes I did. Actually when it was booting. It said the error was the
device was busy.
But after the boot finish and I ran dmesg, it seems the soundcard was
initialized and working right, at least to me. This is part of the
dmesg:

Sound initialization started
Sound initialization complete

and at the end it said:

sb_card: I/O, IRQ, and DMA are mandatory
<SoundBlaster EMU8000 (RAM512k)>

The complete dmesg is attached at end of this e-mail.

If I try insmod, I will get this message:

sb.o: unresolved symbol unload_uart401_Rsmp_ecfdd9c9
sb.o: unresolved symbol attach_uart401_Rsmp_45af1327
sb.o: unresolved symbol uart401intr_Rsmp_6391d066
sb.o: unresolved symbol probe_uart401_Rsmp_6467f99b
 
in /lib/modules/2.2.13/misc I have these files:
sb.o  awe_wave.o  es1371.o  parport_probe.0 uart401.o
uart6850.o

Does anybody has any idea about the problem? Or any suggestion that I
have to try?
Thanks in advance.


---dmesg
output----------------------------------------------------------------
> dmesg
Linux version 2.2.13 (root@linuxdest.CANBF) (gcc version egcs-2.91.66
19990314/Linux (egcs-1.1.2 release)) #1 SMP Sat Jan 1 17:58:12 AST 2000
mapped APIC to ffffe000 (002b4000)
mapped IOAPIC to ffffd000 (002b5000)
Detected 400912958 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 399.77 BogoMIPS
Memory: 127556k/131008k available (1264k kernel code, 424k reserved,
1708k data, 56k init)
VFS: Diskquotas version dquot_6.4.0 initialized
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
per-CPU timeslice cutoff: 100.22 usecs.
CPU0: Intel Pentium II (Deschutes) stepping 03
SMP motherboard not detected. Using dummy APIC emulation.
PCI: PCI BIOS revision 2.10 entry at 0xf06a0
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
Initializing RT netlink socket
Starting kswapd v 1.5 
parport0: PC-style at 0x378 [SPP,ECP,ECPEPP,ECPPS2]
parport0: detected irq 7; use procfs to enable interrupt-driven
operation.
Detected PS/2 Mouse Port.
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.9)
Sound initialization started
Sound initialization complete
Linux video capture interface: v1.00
RAM disk driver initialized:  16 RAM disks of 4096K size
loop: registered device at major 7
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
hda: FUJITSU MPD3084AT, ATA DISK drive
hdb: TOSHIBA CD-ROM XM-6102B, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: FUJITSU MPD3084AT, 8063MB w/512kB Cache, CHS=1027/255/63, UDMA
hdb: ATAPI 24X CD-ROM drive, 256kB Cache
Uniform CDROM driver Revision: 2.56
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8
ne2k-pci.c:vpre-1.00e 5/27/99 D. Becker/P. Gortmaker
http://cesdis.gsfc.nasa.gov/linux/drivers/ne2k-pci.html
ne2k-pci.c: PCI NE2000 clone 'Winbond 89C940' at I/O 0xb800, IRQ 10.
eth0: Winbond 89C940 found at 0xb800, IRQ 10, 00:20:78:17:C0:68.
rtl8139.c:v1.07 5/6/99 Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/rtl8139.html
eth1: RealTek RTL8139 Fast Ethernet at 0xd000, IRQ 9, 00:00:b4:a8:36:1a.
Partition check:
 hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
NTFS version 990411
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 56k freed
Adding Swap: 130748k swap-space (priority -1)
Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996
sb_card: I/O, IRQ, and DMA are mandatory
<SoundBlaster EMU8000 (RAM512k)>