🚀 go-pugleaf

Hi!
All my tries mto use one of the newer kernels failed. I tried already:
1.3.57, 1.3.59, 1.3.92, 1.3.93, 1.3.95, 1.3.97, pre2.0.7
but everytime the same: after a few minutes (up to 15 min) the kernel
crashes... (the correct crash message I didn't wrote down, because it
was too long and I would have to type it into the computer again..., but
I include some config files and other stuff and a crash message which is
an example for all the varieties of crash messages)
When starting the computer there appears everytime a line like this (see
dmesg included):
  fcntl_setlk() called by process 154 (lpd) with broken flock() emulation
with lpd, cron and sendmail...


My system:	486 DX-4 100
		ASUS SP-3G PCI Board
		NCR Controller
		16 MB RAM
		SMC Elite Combo Netcard
		(the rest is visible when you read the dmesg I incl.)
config File of pre0.7 is also included
Please help me. I would be very thankful. Perhaps something wrong in the
bios? Or something wrong in compiling the kernel?

cu,
		MATZE


# dmesg: #
##########
Console: 16 point font, 400 scans
Console: colour VGA+ 80x25, 1 virtual console (max 63)
pcibios_init : BIOS32 Service Directory structure at 0x000fc310
pcibios_init : BIOS32 Service Directory entry at 0xfc740
pcibios_init : PCI BIOS revision 2.00 entry at 0xfc770
Probing PCI hardware.
Calibrating delay loop.. ok - 49.87 BogoMIPS
Memory: 14592k/16384k available (784k kernel code, 384k reserved, 624k data)
This processor honours the WP bit even when in supervisor mode. Good.
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.12 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: ICMP, UDP, TCP
VFS: Diskquotas version dquot_5.6.0 initialized^M
Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.
Checking 'hlt' instruction... Ok.
Linux version 1.99.7 (root@graf_zahl) (gcc version 2.7.0) #1-pre-2.0 Sat May 25
00:37:35 MET DST 1996
Serial driver version 4.12 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
tty01 at 0x02f8 (irq = 3) is a 16550A
tty03 at 0x02e8 (irq = 3) is a 16550A
lp1 at 0x0378, (polling)
ftape-2.08 960314 for Linux 1.3.70
Floppy drive(s): fd0 is 1.44M
Started kswapd v 1.4.2.2
FDC 0 is a National Semiconductor PC87306
scsi-ncr53c7,8xx : at PCI bus 0, device 1,  function 0
scsi-ncr53c7,8xx : NCR53c810 at memory 0xfbfff000, io 0xe800, irq 10
scsi0 : burst length 8
scsi0 : reset ccf to 3 from 0
scsi0 : NCR code relocated to 0x14600 (virt 0x00014600)
scsi0 : test 1 started
scsi0 : NCR53c{7,8}xx (rel 17)
scsi : 1 host.
scsi0 : target 0 accepting asynchronous SCSI
scsi0 : setting target 0 to asynchronous SCSI
  Vendor: SEAGATE   Model: ST11900N          Rev: 8010
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
scsi0 : target 6 accepting asynchronous SCSI
scsi0 : setting target 6 to asynchronous SCSI
  Vendor: SONY      Model: CD-ROM CDU-561    Rev: 1.7X
  Type:   CD-ROM                             ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0
scsi : detected 1 SCSI cdrom 1 SCSI disk total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 3310215 [1616 MB] [1.6 GB]
smc-ultra.c:v1.99 4/17/96 Donald Becker (becker@cesdis.gsfc.nasa.gov)
eth0: SMC Ultra at 0x280, 00 00 C0 86 C8 AA, IRQ 11 memory 0xca000-0xcdfff.
Partition check:
 sda: sda1 sda2 < sda5 sda6 sda7 > sda3 sda4
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 16376k swap-space
Max size:271466   Log zone size:2048
First datazone:26   Root inode number 53248
fcntl_setlk() called by process 67 (crond) with broken flock() emulation
fcntl_setlk() called by process 124 (sendmail) with broken flock() emulation
fcntl_setlk() called by process 144 (lpd) with broken flock() emulation
fcntl_setlk() called by process 152 (lpd) with broken flock() emulation
fcntl_setlk() called by process 154 (lpd) with broken flock() emulation



# crash message #
#################
EFLAGS: 00010206
eax: 000002e0   ebx: 00150560   ecx: 00000100   edx: 001dfea4
esi: 00000000   edi: 0020fc24   ebp: 000000b8   esp: 001dea20
ds: 0018   es: 0018   fs: 002b   gs: 0018   ss: 0018
Process swapper (pid: 0, process nr: 0, stackpage=001dcb34)
Stack: 00150560 00014820 00000001 001dea6c 0020fc24 00014820 00000246 00150580
       001e2868 00150560 001e2868 00000001 001dea6c 00014820 001113c0 00000000
       00000001 ffffffff 00000001 00207fc8 001175eb 001dea88 001deb14 00000000
Call Trace: [<00150560>] [<00150580>] [<00150560>] [<001113c0>] [<001175eb>] [<0
010a50b>] [<001095cf>]
       [<00109633>] [<0010a582>] [<00109370>] [<001c0018>] [<001091d7>]
Code: 8b 31 fa 83 79 10 00 75 2b 8b 41 1c 05 30 75 00 00 39 44 24
Aiee, killing interrupt handler
kfree of non-kmalloced memory: 001deb74, next= 00000000, order=0
kfree of non-kmalloced memory: 001deb64, next= 00000000, order=0
kfree of non-kmalloced memory: 001def98, next= 00000000, order=0
idle task may not sleep
idle task may not sleep
idle task may not sleep
idle task may not sleep
idle task may not sleep



# .config #
###########
#
# Code maturity level options
#
# CONFIG_EXPERIMENTAL is not set

#
# Loadable module support
#
CONFIG_MODULES=y
# CONFIG_MODVERSIONS is not set
# CONFIG_KERNELD is not set

#
# General setup
#
# CONFIG_MATH_EMULATION is not set
CONFIG_NET=y
# CONFIG_MAX_16M is not set
CONFIG_PCI=y
CONFIG_SYSVIPC=y
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_ELF=y
CONFIG_KERNEL_ELF=y
# CONFIG_M386 is not set
CONFIG_M486=y
# CONFIG_M586 is not set
# CONFIG_M686 is not set

#
# Floppy, IDE, and other block devices
#
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_DEV_IDE is not set

#
# Please see drivers/block/README.ide for help/info on IDE drives
#
# CONFIG_BLK_DEV_HD_ONLY is not set

#
# Additional Block Devices
#
# CONFIG_BLK_DEV_LOOP is not set
# CONFIG_BLK_DEV_MD is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_BLK_DEV_XD is not set

#
# Networking options
#
CONFIG_FIREWALL=y
CONFIG_NET_ALIAS=y
CONFIG_INET=y
CONFIG_IP_FORWARD=y
# CONFIG_IP_MULTICAST is not set
CONFIG_IP_FIREWALL=y
CONFIG_IP_FIREWALL_VERBOSE=y
# CONFIG_IP_ALWAYS_DEFRAG is not set
# CONFIG_IP_ACCT is not set
# CONFIG_IP_ROUTER is not set
# CONFIG_NET_IPIP is not set
CONFIG_IP_ALIAS=y
#
# (it is safe to leave these untouched)
#
# CONFIG_INET_PCTCP is not set
# CONFIG_INET_RARP is not set
# CONFIG_NO_PATH_MTU_DISCOVERY is not set
CONFIG_IP_NOSR=y
CONFIG_SKB_LARGE=y

#
#  
#
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_AX25 is not set
# CONFIG_NETLINK is not set

#
# SCSI support
#
CONFIG_SCSI=y

#
# SCSI support type (disk, tape, CDrom)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
CONFIG_BLK_DEV_SR=y
# CONFIG_CHR_DEV_SG is not set

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set

#
# SCSI low-level drivers
#
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
CONFIG_SCSI_NCR53C7xx=y
# CONFIG_SCSI_NCR53C7xx_sync is not set
# CONFIG_SCSI_NCR53C7xx_FAST is not set
# CONFIG_SCSI_NCR53C7xx_DISCONNECT is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_AM53C974 is not set
#
# Network device support
#
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
# CONFIG_EQUALIZER is not set
# CONFIG_PLIP is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_RADIO is not set
CONFIG_NET_ETHERNET=y
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_LANCE is not set
CONFIG_NET_VENDOR_SMC=y
# CONFIG_WD80x3 is not set
CONFIG_ULTRA=y
# CONFIG_SMC9194 is not set
# CONFIG_NET_ISA is not set
# CONFIG_NET_EISA is not set
# CONFIG_NET_POCKET is not set
# CONFIG_TR is not set
# CONFIG_ARCNET is not set

#
# ISDN subsystem
#
# CONFIG_ISDN is not set

#
# CD-ROM drivers (not for SCSI or IDE/ATAPI drives)
#
# CONFIG_CD_NO_IDESCSI is not set

#
# Filesystems
#
CONFIG_QUOTA=y
# CONFIG_LOCK_MANDATORY is not set
CONFIG_MINIX_FS=m
# CONFIG_EXT_FS is not set
CONFIG_EXT2_FS=y
# CONFIG_XIA_FS is not set
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
# CONFIG_VFAT_FS is not set
# CONFIG_UMSDOS_FS is not set
CONFIG_PROC_FS=y
CONFIG_NFS_FS=y
# CONFIG_ROOT_NFS is not set
CONFIG_SMB_FS=y
CONFIG_ISO9660_FS=y
# CONFIG_HPFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_UFS_FS is not set

#
# Character devices
#
CONFIG_SERIAL=y
# CONFIG_DIGI is not set
# CONFIG_CYCLADES is not set
# CONFIG_STALDRV is not set
# CONFIG_RISCOM8 is not set
CONFIG_PRINTER=y
# CONFIG_BUSMOUSE is not set
# CONFIG_PSMOUSE is not set
# CONFIG_MS_BUSMOUSE is not set
# CONFIG_ATIXL_BUSMOUSE is not set
# CONFIG_UMISC is not set
# CONFIG_QIC02_TAPE is not set
CONFIG_FTAPE=y

#
# Set IObase/IRQ/DMA for ftape in ./drivers/char/ftape/Makefile
#
# CONFIG_APM is not set
# CONFIG_WATCHDOG is not set
# CONFIG_RTC is not set

#
# Sound
#
# CONFIG_SOUND is not set

#
# Kernel hacking
#
# CONFIG_PROFILE is not set

-- 
                                                      \\\
                                                    ( o o )
----------------------------------------------o00o----()----o00o-----
| Matthias Schreiber                                                |
| e-Mail: schreibe@informatik.uni-muenchen.de   .oooO               |
| WWW:    http://www.lrz-muenchen.de/a/a2822bi  (   )   Oooo.       |
-------------------------------------------------\ (----(   )--------
                                                  \_)    ) /
                                                        (_/