Thread View: comp.os.os2.networking.misc
3 messages
3 total messages
Started by johnr
Thu, 29 Aug 1996 00:00
Please help with TRAP in PROTMAN
Author: johnr
Date: Thu, 29 Aug 1996 00:00
Date: Thu, 29 Aug 1996 00:00
66 lines
2919 bytes
2919 bytes
I hope I can get some help with the following problem.
I'm trying to install Warp Connect Blue. The installation procedure
installs the OS fine and seems to install the networking component
correctly as well (just TCP/IP 3.0 off the parallel port), but when the
system automatically reboots I get the following trap
==================================================================
Exception in device driver: PROTMAN$
TRAP 000d ERRCD=7074 ERACC=**** ERLIM=********
EAX=000001c8 EBX=abca01c8 ECX=0003024 EDX=00007077
ESI=abda0000 EDI=00030003 EBP=00004d56 FLG=00213206
CS:EIP=0800:000006f9 CSACC=009b CSLIM=0000321c
SS:ESP=0030:00004d44 SSACC=1097 SSLIM=00003fff
DS=07f8 DSACC=0093 DSLIM=00005414 CR0=8001001b
ES=0017 ESACC=00f3 ESLIM=00000fff CR2=abf1e070
FS=0000 FSACC=**** FSLIM=********
GS=0000 GSACC=**** GSLIM=********
The system detected an internal processing error at
location ##0160:fff5c364 - 000d:a364.
60000, 9084
05860524
Internal revision 8.209, 94/11/09
The system is stopped. Record all of the above information and
contact your service representative.
==================================================================
If I remove the PROTMAN.OS2 line, Warp boots - but then I can't
connect to my ISP.
My system:
Pentium 90, 512k cache, AMI BIOS
32Mb RAM
1.2 Gb HDD
Pioneer 4x CD
Diamond Stealth 64 Video VRAM
SoundBlaster 16 PnP
I've had Warp running on this machine for over a year. Last week I tried
to refresh the system by undergoing a new install and this turns up!
My tech people have changed the CPU, CPU fan, memory. Recently I've changed
the power supply, graphics card, sound card and CDROM. Yesterday I
purchased an industrial strength power line filter and spike suppressor.
I've run diagnostics on the CDROM all night (under native DOS and a VDM).
If the problem is a hardware fault, I don't know where else to look (perhaps
the serial card?)! Could the Connect CD itself be damaged? How do I check
this?
Please HELP!
TIA
John
_________
John Roumeliotis | finger for PGP public key
Computer and Mathematical Sciences | E-Mail: johnr@matilda.vut.edu.au
Victoria University of Technology | WWW: http://dingo.vut.edu.au/~johnr
Re: Please help with TRAP in PROTMAN
Author: vilez
Date: Sun, 01 Sep 1996 00:00
Date: Sun, 01 Sep 1996 00:00
46 lines
1885 bytes
1885 bytes
In <DwvrF0.BoH@matilda.vut.edu.au>, johnr@warp.vut.edu.au writes:
>I hope I can get some help with the following problem.
>
>I'm trying to install Warp Connect Blue. The installation procedure
>installs the OS fine and seems to install the networking component
>correctly as well (just TCP/IP 3.0 off the parallel port), but when the
>system automatically reboots I get the following trap
>
>==================================================================
>
>Exception in device driver: PROTMAN$
[snip]
>The system is stopped. Record all of the above information and
>contact your service representative.
>
>==================================================================
>
>If I remove the PROTMAN.OS2 line, Warp boots - but then I can't
>connect to my ISP.
>
[snip]
No final answers but,
If installing Warp Connect over Warp with Bonus Pak TCP/IP,
you need to remove TCP/IP 2.x first.
Check LANTRAN.LOG. There might be something useful here.
Replace PROTMAN.OS2 with a known good copy.
Check PROTOCOL.INI for "bad" or incorrect entries.
CHKDSK
I suggest:
Remove TCP/IP 2.x
Check/edit CONFIG.SYS
Install Warp Connect w/o networking
When up and running, then install Networking.
(dbl.-check that parallel support is installing)
Hope some of these ideas gets you results.
Mark Vilez
Re: Please help with TRAP in PROTMAN
Author: johnr
Date: Mon, 02 Sep 1996 00:00
Date: Mon, 02 Sep 1996 00:00
60 lines
2626 bytes
2626 bytes
In <50cneu$2a9o@news-s01.ny.us.ibm.net>, vilez@ibm.net writes: >In <DwvrF0.BoH@matilda.vut.edu.au>, johnr@warp.vut.edu.au writes: >>I hope I can get some help with the following problem. >> >>I'm trying to install Warp Connect Blue. The installation procedure >>installs the OS fine and seems to install the networking component >>correctly as well (just TCP/IP 3.0 off the parallel port), but when the >>system automatically reboots I get the following trap >> >>================================================================== >> >>Exception in device driver: PROTMAN$ >[snip] >>The system is stopped. Record all of the above information and >>contact your service representative. >> >>================================================================== >> >>If I remove the PROTMAN.OS2 line, Warp boots - but then I can't >>connect to my ISP. >> >[snip] > >No final answers but, > If installing Warp Connect over Warp with Bonus Pak TCP/IP, > you need to remove TCP/IP 2.x first. > > Check LANTRAN.LOG. There might be something useful here. > > Replace PROTMAN.OS2 with a known good copy. > > Check PROTOCOL.INI for "bad" or incorrect entries. > > CHKDSK > > >I suggest: > Remove TCP/IP 2.x > Check/edit CONFIG.SYS > Install Warp Connect w/o networking > When up and running, then install Networking. > (dbl.-check that parallel support is installing) > >Hope some of these ideas gets you results. > >Mark Vilez I was trying to install Warp Connect on a bare system - no TCP/IP 2.0. One of your suggestions did work. I installed the base OS first and then the networking. Thanks also to John Summerfield for pointing out that updates to MPTS and TCPIP are available. John _________ John Roumeliotis | finger for PGP public key Computer and Mathematical Sciences | E-Mail: johnr@matilda.vut.edu.au Victoria University of Technology | WWW: http://dingo.vut.edu.au/~johnr
Thread Navigation
This is a paginated view of messages in the thread with full content displayed inline.
Messages are displayed in chronological order, with the original post highlighted in green.
Use pagination controls to navigate through all messages in large threads.
Back to All Threads