Thread View: comp.os.os2
2 messages
2 total messages
Started by Ronald Gonzalez
Wed, 12 Feb 2003 16:10
PCMCI Enabler under OS/2 4.5
Author: Ronald Gonzalez
Date: Wed, 12 Feb 2003 16:10
Date: Wed, 12 Feb 2003 16:10
32 lines
2654 bytes
2654 bytes
Hello there. I am having problems when enabling a PCMCI ethernet card in a Thinkpad Iseries 1400 (type 2621-420) running under OS/2 Warp 4.5. The enabler from OS/2 says that the card doesnt exist, but if I run it this from a Dos sesion the card is detected by the enabler. ---config.sys --- .... .... .... BASEDEV=PCMCIA.SYS DEVICE=C:\THINKPAD\VPCMCIA.SYS DEVICE=C:\THINKPAD\PCMSSDIF.SYS DEVICE=C:\THINKPAD\PCM2SRAM.SYS DEVICE=C:\THINKPAD\FLSH2MTD.SYS DEVICE=C:\THINKPAD\PCM2FLSH.SYS BASEDEV=PCM2ATA.ADD /S:2 /!DM /NOBEEP DEVICE=C:\OS2\BOOT\COM.SYS DEVICE=C:\OS2\MDOS\VCOM.SYS BASEDEV=OS2PCARD.DMD BASEDEV=AUTODRV2.SYS c:\os2\autodrv2.ini DEVICE=C:\IBMCOM\MACS\ECARD.OS2 /irq=3 /io=360 <=THIS IS THE ENABLER.... DEVICE=C:\IBMCOM\MACS\PCMND.OS2 <=THE ETHERNET DRIVER DEVICE=C:\THINKPAD\$ICPMOS2.SYS /G BASEDEV=IBM2SS04.SYS .... -------------------- Once I could configure and worked but after restarting didnt anymore! Any sugestion ?
Re: PCMCI Enabler under OS/2 4.5
Author: Assover
Date: Thu, 06 Mar 2003 23:05
Date: Thu, 06 Mar 2003 23:05
42 lines
2721 bytes
2721 bytes
"Ronald Gonzalez" <rggonzalez@asociacioncibao.com.do> wrote in message news:<HvOcnZwiKelG7NejXTWc3A@codetel.net.do>... > Hello there. > I am having problems when enabling a PCMCI ethernet card in a Thinkpad > Iseries 1400 (type 2621-420) running under OS/2 Warp 4.5. > The enabler from OS/2 says that the card doesnt exist, but if I run it this > from a Dos sesion the card is detected by the enabler. > > ---config.sys --- > .... > .... > .... > BASEDEV=PCMCIA.SYS > DEVICE=C:\THINKPAD\VPCMCIA.SYS > DEVICE=C:\THINKPAD\PCMSSDIF.SYS > DEVICE=C:\THINKPAD\PCM2SRAM.SYS > DEVICE=C:\THINKPAD\FLSH2MTD.SYS > DEVICE=C:\THINKPAD\PCM2FLSH.SYS > BASEDEV=PCM2ATA.ADD /S:2 /!DM /NOBEEP > DEVICE=C:\OS2\BOOT\COM.SYS > DEVICE=C:\OS2\MDOS\VCOM.SYS > BASEDEV=OS2PCARD.DMD > BASEDEV=AUTODRV2.SYS c:\os2\autodrv2.ini > DEVICE=C:\IBMCOM\MACS\ECARD.OS2 /irq=3 /io=360 <=THIS IS THE > ENABLER.... > DEVICE=C:\IBMCOM\MACS\PCMND.OS2 <=THE ETHERNET > DRIVER > DEVICE=C:\THINKPAD\$ICPMOS2.SYS /G > BASEDEV=IBM2SS04.SYS > .... > -------------------- > > Once I could configure and worked but after restarting didnt anymore! > Any sugestion ? I remember that some PCMIA ethernet cards use a point type driver which enables the card independent of the general OS/2 PCMCIA drivers. You may try disabling the general OS/2 enabler for the particular slot you are placing the card in. It may also be necessary to reserve the IRQ / IO resources required by the card at the beginning of config sys. But I'd try step one first, and see how you go. Good luck.
Thread Navigation
This is a paginated view of messages in the thread with full content displayed inline.
Messages are displayed in chronological order, with the original post highlighted in green.
Use pagination controls to navigate through all messages in large threads.
Back to All Threads