Thread View: pdx.utek
2 messages
2 total messages
Started by Tom Laird
Wed, 30 Sep 1992 18:21
6130 SCSI drive error codes
Author: Tom Laird
Date: Wed, 30 Sep 1992 18:21
Date: Wed, 30 Sep 1992 18:21
8 lines
971 bytes
971 bytes
I have been running a CDC-702 SCSI driveo n a 6130 for several months now. I recently have run into problems with erros messages showing up all of the time on my screen. The error message I get is "<Utek> sense key=1 extended sense=15" "disk block number 274836". I reformatted the drive, fsck goes through with no problems. When I went to run scsifmt it came on at first and said "MPAT corrupted" three times. I got no errors formatting the drive. Does anyone have any help for me on this problem?
Re: 6130 SCSI drive error codes
Author: Jeff Beadles
Date: Thu, 01 Oct 1992 03:31
Date: Thu, 01 Oct 1992 03:31
87 lines
3868 bytes
3868 bytes
lairdt@storm.CS.ORST.EDU (Tom Laird) writes:
>I have been running a CDC-702 SCSI driveo n a 6130 for several months now.
>I recently have run into problems with erros messages showing up all of the
>time on my screen. The error message I get is "<Utek> sense key=1 extended
>sense=15" "disk block number 274836". I reformatted the drive, fsck goes
>through with no problems. When I went to run scsifmt it came on at first
>and said "MPAT corrupted" three times. I got no errors formatting the drive.
>Does anyone have any help for me on this problem?
Well, it appears that the drive is trying to seek to an invalid
position on the drive. Here's a (brief) list of SCSI errors that
I haved around here...
Sense key:
0H: No sense (No error)
1H: Recovered error (retried sucessfully)
2H: Not ready (device can not be accessed)
3H: Medium error (Media error)
4H: Hardware error (controller error)
5H: Illegal request (Invalid CDB parameter)
6H: Unit attention (unit has been reset)
7H: Data Protect (read/write protected device)
BH: Aborted command (Command aborted)
EH: Miscompare (Checksum error)
Extended sense:
00H: None additional info available
01H: No Index/sector signal
02H: No seek complete
03H: Write fault
04H: Drive not ready
05H: Drive not selected
06H: No track zero found
07H-0FH: Reserved
10H: ID CRC error
11H: Unrecovered read
12H: No address mark found in id field
13H: No address mark found in data field
14H: No record found
15H: Seek positioning error
16H: Reserved
17H: Recovered read (with retries)
18H: Recovered read (with ECC)
19H: Defect list error
1AH: Parameter overrun
1BH: Reserved
1CH: Primary defect list not found
1DH-1FH: Reserved
20H: Invalid command code
21H: Invalid logical block address
22H-23H: Reserved
24H: Illegal field in CDB
25H: Invalid LUN
26H: Invalid field parameter list
27H: Write protected
28H: Reserved
29H: Poweron reset or bus device reset
2AH: Mode select parameters changed
2BH-30H: Reserved
31H: Format failed
32H: No defect spare location available
33H-3FH: Reserved
40H: Ram failure
41H: Data path diag failure
42H: Power on diag failure
43H: Message reject
44H: SCSI hardware/firmware error
45H: Select/reselect failed
46H: Reserved
47H: SCSI parity error
48H: Initiator detected error
49H: Inappropriate/Illegal message
4AH-69H: Reserved
6AH: Format required
6BH-6F: Reserved
70H-7FH: Selftest '7x' failed
80H-8BH: Correctable ECC error. (# bits == {0=b})
8CH-8FH: Reserved
90H: Configuration error
91H-FFH: Reserved
-Jeff
--
Jeff Beadles jeff@onion.rain.com
Thread Navigation
This is a paginated view of messages in the thread with full content displayed inline.
Messages are displayed in chronological order, with the original post highlighted in green.
Use pagination controls to navigate through all messages in large threads.
Back to All Threads