🚀 go-pugleaf

--
In article <10266@cimshop.UUCP>, vchow@helios.UUCP (Victor Chow) writes:
>Path: msuinfo!srvr1.engin.umich.edu!uunet!cimshop!helios!vchow
>
>In article <C164Hn.223@dscomsa.desy.de> you write:
>|> In article <1993Jan20.164619.8700@eecs.nwu.edu>, shil@eecs.nwu.edu 
>|>   (Lei Shi) writes:
>|> 
>|> |>
>|> |>Hi: 
>|> |>  ... My question is how I can measure the total CPU used by the 
>|> |> execution of the program ... in VMS ...
>|> |>					Your Sincerely,
>|> |>
>|> |>					Lei Shi
>|> 
>|> The are various alternatives. The simplest way is to run your program as 
>|> a batch job.   ...   Otherwise, you can use
>|> the $ SHOW PROC /ACC for an interactive session but that cannot (as far as
>|> I am aware) be zeroed before execution of a program. Finally, if this is not
>|> sufficient you should investigate the run time library timer routine
>|> LIB$SHOW_TIMER, LIB$STAT_TIMER ... (try $ HELP RTL LIB$ *TIMER*.
>|> 
>
>Lei Shi,
>
>Using LIB$ or SYS$ calls allow you to get accurate accounting information about
>a process the way you want.  The disadvantage is that you have to modify your
>source code to do so (and provided that you still have the source code).
>
>Submitting an image to a batch job and get the accounting information from the 
>log file should get what you need.  However your LOGIN.COM and the system
>SYLOGIN.COM should be relatively short and do not run resource hogging command
>s or images (relative to your actual image).  Otherwise the accouting info of
>the batch job does not accurately reflect the resources used by your image
>only. Remember that a VMS batch job includes not only the images/commands you
>want run, but also other commands or images (such as LOGIN.COM and SYLOGIN.COM,
>etc) that are executed as part of the batch job.
>
>Another simple alternative that requires no modification to your code and LOGIN/SYLOGIN.COM is to do the following steps:
>
>1. create a file, say, your_image.COM like this:
>    $ run your_image.EXE        or (@ your_dcl.COM)
>    $ logout/full
>
>2. then at the DCL prompt, enter
>    SPAWN @your_image.COM
>
>The SPAWN starts a child process which starts with "zeroed" accounting info to 
>run your image and the "logout/full" command.  The "Accounting information" 
>that logout/full prints should be very close to what "your_image" needs (plus 
>the overhead needed by the SPAWN(?), @your_image.COM, and "logout/full",etc).  
>(I assume your program takes a lot more resources to run than a simple SPAWN
>command.) 
>
>As long as you are not trying to precisely measure a tiny image that uses very 
>little resource and that you don't need to get the process' accounting info at 
>different parts of your image, this simple method should be adequate. 
>
>Good luck!  8-)
>
>Victor
>
>
>
>
>
>
>
 Non invasive timings can be gotten via:

SHOW PROCESS/ACCOUTING
RUN YOUR_IMAGE
SHOW PROCESS/ACCOUTING

and doing some simple subtractions. 
	RF.
Ron Fox                     | FOX@MSUNSCL.BITNET      | Where the name 
NSCL                        | FOX@RUDOLF.NSCL.MSU.EDU | goes on before
Michigan State University   | MSUHEP::RUDOLF::FOX     | the quality
East Lansing, MI 48824-1321 |                         | goes in.
USA