Request information for Maxitor 7080AT, 7213AT

Thread View: comp.sys.ibm.pc

4 messages

[T] Back to Threads [V] Tree View [G] Group Articles

4 total messages Started by Mike Chang Wed, 23 Dec 1992 01:58

#14050

Author: Mike Chang
Date: Wed, 23 Dec 1992 01:58

17 lines
1087 bytes

Hi,

I recently bought two used maxitor drives without documents. I was
wondering if anyone can find the parameters for Maxitor 7080AT and
7212AT (cylinder,head,sector number,etc). I also would like know
what the jumper settings are for master,slave and single drive
configurations. Thanks much.

Happy holiday.

Mike
--
   The opinions expressed are not necessarily those of the University of
     North Carolina at Chapel Hill, the Campus Office for Information
        Technology, or the Experimental Bulletin Board Service.
           internet:  laUNChpad.unc.edu or 152.2.22.80

Re: Request information for Maxitor 7080AT, 7213AT

#14051

Author: Mike Chang
Date: Wed, 23 Dec 1992 02:03

18 lines
1189 bytes

>I recently bought two used maxitor drives without documents. I was
>wondering if anyone can find the parameters for Maxitor 7080AT and
>7212AT (cylinder,head,sector number,etc). I also would like know
 ------
>what the jumper settings are for master,slave and single drive
>configurations. Thanks much.
>
>Happy holiday.


Oops, I meant 7213AT drive.

--Mike
--
   The opinions expressed are not necessarily those of the University of
     North Carolina at Chapel Hill, the Campus Office for Information
        Technology, or the Experimental Bulletin Board Service.
           internet:  laUNChpad.unc.edu or 152.2.22.80

NEC vs Everyone else!

#14052

Author: Martin Tichy
Date: Wed, 23 Dec 1992 02:38

15 lines
1162 bytes

Just to be a little more detailed on what I posted earlier.  
I'm looking for a high end 17" monitor that will be able to do 
1280 x 1024 x 256 at 74Hz NI, have front panel controls, the 
ability to use the full screen, degaussing, digital presets,
and it must look bright and sharp.
 
So far I hear the NEC 5fg is the way to go.  For it's cost 
however I can get some 20" monitors.  So what is the best 
monitor I can get for $1800 Canadian or less?
 
Other CRTs I'm considering right now are the MAG 17f, 
Viewsonic 7, and the Nanao 560ti. Can I get some specs on any 
of the monitors mentioned or anything else in that price range?
 
Merry Christmas!

Re: Request information for Maxitor 7080AT, 7213AT

#14055

Author: Ken Thomson
Date: Mon, 28 Dec 1992 06:11

40 lines
1913 bytes

In article <1992Dec23.020307.11722@samba.oit.unc.edu> Mike.Chang@launchpad.unc.edu (Mike Chang) writes:

>>I recently bought two used maxitor drives without documents. I was
>>wondering if anyone can find the parameters for Maxitor 7080AT and
>>7212AT (cylinder,head,sector number,etc). I also would like know
> ------
>>what the jumper settings are for master,slave and single drive
>>configurations. Thanks much.
>>
>>Happy holiday.
>
>Oops, I meant 7213AT drive.

Maxtor 7213AT
=============

Master/Slave                    J20      J19     J18     J17

Only drive in system             J        J

Master drive in dual system      J        O

Slave drive in dual system       O        J

(where J=jumpered, O=open)

Common AT BIOS Parameters :-

                                 CYL       HEADS     SPT    MBYTES    TYPE
Maxtor 7213AT                    683        16       38     203        47

WPC, and Landing Zone entries do not need to be specified.  The IDE
interface will ignore an set values for these 2 fields.

Hope that will help you.
-- 
Ken Thomson. (kthomson@extro.ucc.su.OZ.AU)        #include "std_disclaimer"

"To err is human, but to really &^$% things up takes a computer."
--

Thread Navigation

This is a paginated view of messages in the thread with full content displayed inline.

Messages are displayed in chronological order, with the original post highlighted in green.

Use pagination controls to navigate through all messages in large threads.

Back to All Threads