Thread View: comp.sys.ibm.pc.rt
6 messages
6 total messages
Started by Brad Craig
Wed, 27 Jun 1990 17:18
Moving data from RS 6000 to RT 125 via tape.
Author: Brad Craig
Date: Wed, 27 Jun 1990 17:18
Date: Wed, 27 Jun 1990 17:18
31 lines
1868 bytes
1868 bytes
Hello RS users! Are we having fun yet?
Here is my problem:
I'm trying to write write some data to a tape from an RS 6000, and
then read the tape on an RT 125. The RS is running with the 9021
build of version 3. The RT is running version 2.2.1. SO far I have
not been able to read any tape on the RT that was created on the RS.
I have attempted everything from dd to backup. I have used the '-o'
flag with the backup command, just as it is stated in the manual page.
I also set the ECC flag to disable for the tape device (instructions
form IBM), using smit.
When I use 'dd' I get a message of "0+0 records in ...". When I
use tar I get "0 blocks on tape". When I use backup, and attempt to
restore the tape, I get "Tape not in backup format". When I use cpio,
it just gets lost. I have tried combinations of tar, cpio, backup
piped to dd, still no succes.
I am using an RT 125 with a high-density tape drive. (don't know
the model right off hand, but it is an IBM drive)
Has anybody out there done this? I've contacted IBM AIX support
for the RS, but they haven't given me any solutions that have worked.
Thanks in advance.
Brad Craig "Look at the (513) 865-1536
Mead Data Central size of those Interactive Systems
P.O. Box 933 winches!" mead!brad@uccba.uc.edu
Dayton, Ohio 45401 Dave Letterman ...!uccba!mead!brad
Re: Moving data from RS 6000 to RT 125 via tape.
Author: Dave Edmondson
Date: Thu, 28 Jun 1990 04:23
Date: Thu, 28 Jun 1990 04:23
19 lines
1287 bytes
1287 bytes
In article <807@meaddata.mead.UUCP> brad@mead.UUCP (Brad Craig) writes:
brad> [... trouble writing tapes ...]
this is from memory - so may be wrong (!).
the rs/6000 can read/write qic150, and can read qic24. the rt will
(almost certainly) not read qic150. i talked to someone at ibm about
this quite a while ago and the answer was `they are expected to be on
a network'. if this is the case, then you can move stuff from rt to
rs/6000, but not the other way.
anyone from ibm (or elsewhere) care to correct me here ?
dave.
--
Dave Edmondson
Department of Computing, Imperial College, 180 Queen's Gate, London SW7 1BZ UK
phone: 071-589-5111 x5085 fax: 071-581-8024
dme@doc.ic.ac.uk, ..!ukc!icdoc!dme, dme@athena.mit.edu
Re: Moving data from RS 6000 to RT 125 via tape.
Author: Peter Blemel
Date: Thu, 28 Jun 1990 08:11
Date: Thu, 28 Jun 1990 08:11
6 lines
670 bytes
670 bytes
1.) Your RT must have the -002 tape drive to read the QIK-150 (sp?) format of
the RS/6000.
2.) Use /dev/rmt?.4 to write on the RS/6000.
Peter Blemel
Re: Moving data from RS 6000 to RT 125 via tape.
Author: John F. Haugh II
Date: Thu, 28 Jun 1990 12:55
Date: Thu, 28 Jun 1990 12:55
9 lines
950 bytes
950 bytes
In article <1990Jun28.081131.9099@ariel.unm.edu> cs3631bs@hydra.unm.edu (Peter Blemel) writes:
>2.) Use /dev/rmt?.4 to write on the RS/6000.
Unless the SCSI address on your tape drive is different. ;-)
--
John F. Haugh II UUCP: ...!cs.utexas.edu!rpp386!jfh
Ma Bell: (512) 832-8832 Domain: jfh@rpp386.cactus.org
Proud Pilot of RS/6000 Serial #1472
Re: Moving data from RS 6000 to RT 125 via tape.
Author: Rob McDonald
Date: Sun, 01 Jul 1990 13:51
Date: Sun, 01 Jul 1990 13:51
12 lines
925 bytes
925 bytes
In article <807@meaddata.mead.UUCP> brad@mead.UUCP (Brad Craig) writes: > ...I'm trying to write write some data to a tape from an RS 6000, and >then read the tape on an RT 125... My understanding from discussions with IBM was that the RS6000 could read but not write a tape for the RT. ...rob -- EMAIL: rob@maccs.dcss.mcmaster.ca <<< Standard Disclaimers Apply >>> ARCHAIC: Steltech, 1375 Kerns Rd., Burlington, Ontario, Canada, L7P 3H8.
Re: Moving data from RS 6000 to RT 125 via tape.
Author: Ken Dillman
Date: Mon, 02 Jul 1990 19:37
Date: Mon, 02 Jul 1990 19:37
26 lines
1963 bytes
1963 bytes
In article <807@meaddata.mead.UUCP> brad@mead.UUCP (Brad Craig) writes: > I'm trying to write write some data to a tape from an RS 6000, and >then read the tape on an RT 125. The RS is running with the 9021 >build of version 3. The RT is running version 2.2.1. SO far I have >not been able to read any tape on the RT that was created on the RS. >I have attempted everything from dd to backup. I have used the '-o' >flag with the backup command, just as it is stated in the manual page. >I also set the ECC flag to disable for the tape device (instructions >form IBM), using smit. > > I am using an RT 125 with a high-density tape drive. (don't know >the model right off hand, but it is an IBM drive) > Brad, place a hardware service call for the tape drive and specifiy that you require the hardware EC that allows tape interchange with the RT (specifically EC 844345). I'm assuming you have a loaner machine from the AIX Porting Center. These machines require a hardware upgrade. The other steps you've done are also required (no ECC, -o on backup). Hope this helps. ----------------------------------------------------------------------------- Ken Dillman | 11400 Burnet Road | Phone: T/L 678-4804 or AIX Technical Support | Austin, TX 78754 | 512/838-4804 ZIP 2830 | | VNET/PROFS: KDILLMAN at AUSTIN
Thread Navigation
This is a paginated view of messages in the thread with full content displayed inline.
Messages are displayed in chronological order, with the original post highlighted in green.
Use pagination controls to navigate through all messages in large threads.
Back to All Threads